Panasonic DMR-EH75V - Manual (Page 79)

79
RQT8346
Channel/Clock settings when TV Guide On Screen ® system is not used
Refer to the control reference on page 74.
Preparation:
If the program listings has already been downloaded, return the unit to the factory preset condition using the steps indicated below.
When the unit is on and stopped
1 Press and hold [CH,
X] and [CH, W] on the main unit for about 5 seconds.
The unit turns off.
2 Press [ Í, DVD/VHS POWER] to turn the unit on.
3 After the language and TV aspect is setup, press [RETURN] and exit the TV Guide
On Screen ® system setup screen.
Note
You can set scheduled recording only manually after you set the unit with “Set Channels
Automatically”.
[1] While stopped
Press [FUNCTIONS].
[2] Press [ 3, 4] to select “Other Functions” and
then press [ENTER].
[3] Press [ 3, 4] to select “Setup” and then press
[ENTER].
[4] Press [ 3, 4] to select “Channel” and then
press [ 1].
[5] Press [ 3, 4] to select “Set Channels
Automatically” and then press [ENTER].
[6] Press [ENTER].
Auto Channel Setting starts. This takes a few minutes.
The unit then proceeds with Auto Clock Setting. The time is
displayed when finished.
≥DST, Daylight Saving Time, shows the summertime setting.
≥TIME ZONE shows the time difference from Greenwich Mean
Time (GMT).
EST (Eastern Standard Time) l GMT j5
CST (Central Standard Time) l GMT j6
MST (Mountain Standard Time) l GMT j7
PST (Pacific Standard Time) l GMT j8
AST (Alaska Standard Time) l GMT j9
HST (Hawaii Standard Time) l GMT j10
For other areas: xx hr
≥If the Auto Clock Setting does not start automatically, select
“Clock Settings” from the “Setup” tab and then select “Set
Clock Automatically”.
≥If the time was not set correctly, use manual clock setting
( l 25) or adjust time zone.
[7] Press [ENTER].
≥Regarding DST (Daylight Saving Time) l 25
≥The unit configures channels according to the Signal Source
(RF IN) settings as follows.
Adjust the time zone ( j1 or i1) if it was not set correctly with auto
clock setting.
You cannot change this setting if you set the clock manually.
[1] While stopped
Press [FUNCTIONS].
[2] Press [ 3, 4] to select “Other Functions” and
then press [ENTER].
[3] Press [ 3, 4] to select “Setup” and then press
[ENTER].
[4] Press [ 3, 4] to select “Setup” and then press
[ 1].
[5] Press [ 3, 4] to select “Clock Settings” and
then press [ENTER].
[6] Press [ 3, 4] to select “Adjust Time Zone” and
then press [ENTER].
≥Regarding DST (Daylight Saving Time) l 25
[7] Press [ 3, 4] to select “s1” or “r1” and then
press [ENTER].
To return to the previous screen
Press [RETURN].
To exit the screen
Press [RETURN] several times.
To cancel partway while Auto Channel/Clock Setting is taking place
Press [RETURN].
To set so the TV Guide On Screen ® system is not displayed automatically when you turn the unit on
When the power is turned on and the Start setup screen is displayed, press [ 3, 4] to select “Don’t remind me again” and press [ENTER].
Auto channel/clock settings
Setup
Disc
Channel
Video
Audio
Display
Set Clock Automatically
Auto Clock Setting is complete.
11/4/2006 12:15 AM
DST.............. On
Time Zone..... CST
Setup
Signal Source
(RF IN)
Band Channel
Antenna
VHF 2 to 13
UHF 14 to 69
CableTV
VHF 2 to 13
CATV LOW BAND 95 to 99
CATV MID/SUPER BAND 14 to 36
CATV HYPER BAND 37 to 65
ULTRA BAND
66 to 94
100 to 125
SPECIAL CATV CHANNEL 1
∫ Adjust Time Zone
Setup
Setup
Audio
Adjust Time Zone
j1
0
i1
Channel
Disc
Video
Ch
a
n
g
in
g
th
e
u
n
it’s se
ttin
g
s/C
h
a
n
n
e
l/Cl
o
ck se
ttin
g
s w
h
e
n
T
V
Gu
id
e
On
S
cr
e
e
n ®
syst
e
m
is n
o
t use
d
M6740P.book 79 ページ ２００６年１月３０日 月曜日 午後３時３０分