Panasonic DMR-EH75V - Manual (Page 24)

24
RQT8346
STEP 2 Setting up the TV Guide On Screen ® system
Refer to the control reference on page 23.
Please perform setup by following all instructions that apply to your current service.
DirecTV/DISH Network service is only available in the United States.
Once setup is finished l 25, Step 7, Confirm the settings.
Service Set the following
Antenna ≥You cannot select both “Antenna” and “Cable without a Cable Box”.
≥Further setup is not necessary.
Cable without a
Cable Box
Cable with a
Cable Box
1 Cable box connection channel (“RF, Channel 2”/ “RF, Channel 3”/ “RF, Channel 4”/ “IN3”)
- Select “IN3”.
(If you are connecting the cable box to this unit’s RF terminal, select “RF, Channel 2”, “RF, Channel 3” or
“RF, Channel 4”, according to the cable box setting.)
2 Are you using a digital service package?
Select “Yes”, “No” or “I don’t know”.
3 Check how the channels are input.
Select how your current cable box inputs 2, 3, and 4-digit numbered channels.
4 Cable box brand
- Move down with [ 4] for more brands.
- You can also press [PAGE W] or [PAGE X] to skip several lines.
- Select “Not Listed” if you cannot find your brand on the list.
5 IR signal code
- Make sure your cable box is set to the channel that appears on screen and then press [ENTER].
The unit begins trying various IR codes to see which one communicates properly with your cable box. It’s quite
common for this phase of the setup to be repeated numerous times.
- If the cable box has changed to channel 09, select “Yes”.
- If the cable box is still set to the same channel, select “No”. Repeat this step until the cable box changes to
channel 09.
If you want to try the code again for some reason, e.g., you accidentally moved the IR Blaster, select “Test this
code again”.
DirecTV
1 Satellite receiver connection channel (“RF, Channel 2”/ “RF, Channel 3”/ “RF, Channel 4”/ “IN3”)
- Select “IN3”.
(If you are connecting the satellite receiver to this unit’s RF terminal, select “RF, Channel 2”, “RF, Channel 3” or
“RF, Channel 4”, according to the satellite receiver setting.)
2 Check how the channels are input.
Select how your current DirecTV receiver inputs 2, 3, and 4-digit numbered channels.
3 Satellite receiver brand
- Move down with [ 4] for more brands.
- You can also press [PAGE W] or [PAGE X] to skip several lines.
4 IR signal code
- Turn your satellite receiver ON and then press [ENTER].
If you are watching DirecTV in 4:3 aspect with the side panel, set the side panel to “Off” on the DirecTV
receiver in order to correctly receive the program listings.
The unit begins trying various IR codes to see which one communicates properly with your satellite receiver. It’s
quite common for this phase of the setup to be repeated numerous times.
Look at the display of the DirecTV receiver.
- If the channel display changes, then select “Yes”.
- If the satellite receiver is still set to the same channel, select “No”. Repeat this step until the satellite receiver
changes the channel.
If you want to try the code again for some reason, e.g., you accidentally moved the IR Blaster, select “Test this
code again”.
DISH Network
≥Satellite receiver connection channel (“RF, Channel 2”/ “RF, Channel 3”/ “RF, Channel 4”/ “IN3”)
- Select “IN3”.
(If you are connecting the satellite receiver to this unit’s RF terminal, select “RF, Channel 2”, “RF, Channel 3” or
“RF, Channel 4”, according to the satellite receiver setting.)
You cannot use the IR Blaster included with this unit.
You cannot set other equipment.
Is your cable box now tuned to channel 09?
Yes
No
Test this code again
Did your satellite receiver change channels?
Yes
No
Test this code again
M6740P.book 24 ページ ２００６年１月３０日 月曜日 午後３時３０分