Dubbing from dvd, One touch dubbing (dvd, L 60 – Panasonic DIGA DMR-E75V User Manual
Page 60: Advanced operations, Vhs dvd, One touch dubbing (dvd l vhs)

Advanced Operations
60
With one stroke of the button, all of contents in the disc
° are
automatically dubbed onto the tape.
° The available disc for dubbing onto the tape are DVD-RAM and
non-finalized DVD-R. If you want to dubbing from DVD-Video or
finalized DVD-R, perform Manual Dubbing. (
Preparation
DVD (Recording source)
≥Press [DVD].
≥Insert the disc containing the programme to be copied. (
≥Playing back DVD.
≥Press [AUDIO] to select the audio you wish to record.
≥Stop the disc. (
l right)
VHS (Recording target)
≥Press [VHS].
≥Insert a video cassette with an intact erasure prevention tab.
(
≥Confirm that the remaining tape time is sufficient for recording.
(
≥Select the recording mode.
Settings (“TV System”
≥When dubbing an NTSC disc to a tape
- Set “TV System” on “Connection” in “SETUP” to “NTSC”.
≥When dubbing a PAL disc to a tape
- Set “TV System” on “Connection” in “SETUP” to “PAL”.
∫To stop dubbing halfway through
Press [
∫, STOP].
∫When starting the One Touch Dubbing from desired
title
During playing back DVD, press [
∫, STOP] on the desired title
(Resume Function
l 18), and then press [VHS —, DUBBING], it will
start dubbing from the beginning of desired title.
≥When starting dubbing from the beginning of DVD, cancel the
resume function (
l 18) and then press [VHS —, DUBBING].
∫When dubbing is started, the following operations also
start automatically:
≥“On-Screen Messages” on Display
) “Off” (l 45)
≥Recording channel indication on VHS
) “DC” (l 61)
≥Output to TV
) VHS output
≥The audio mode of the target tape is fixed to “LR”.
∫Only the following operations are allowed while
dubbing:
≥Stopping dubbing by pressing [∫, STOP].
≥Switching the audio mode by pressing [AUDIO]. The audio which
you are hearing is recorded.
Note
≥You cannot operate for dubbing while timer recording standby on
both DVD and VHS. Cancel the timer recording standby.
≥When “DVD / VHS Output” is set to “Manual” (
l 43), or when DVD
output is selected in starting dubbing, the output is switched to VHS
automatically at the time when dubbing is started.
- When the dubbing is already started, you cannot switch the
output manually.
≥When the dubbing is not started or not executed, the “DUBBING”
indicator blinks for about 7 seconds. Check if the unit is properly
prepared.
≥When menu screen appeared on the TV, one touch dubbing cannot
start. One Touch Dubbing can perform start, after return from menu
screen.
Dubbing from DVD
∫ One Touch Dubbing (DVD
l VHS)
SLOW/
SEARCH
REW
FF
SKIP/INDEX
PLAY
STOP
PAUSE
FUNCTIONS
DIRECT NAVIGATOR
µ
DVD/VHS
CREATE
CHAPTER
TRACKING/V-LOCK
DVD/VHS
CANCEL/RESET
INPUT SELECT
DIRECT TV REC
VHS
G-Code
CREATE
CHAPTER
CH
AV
VOLUME
DVD
CH,
W, X
DUBBING
AUDIO
EXT LINK
VHS REC
DVD REC
REC MODE
TIMER
VHS
DVD
JET REW
DVD
VHS
1
;
∫
:, 9
AUDIO
REC MODE
VHS
—
OPEN/CLOSE
TIME SLIP
REC
CH
/
k1.3
DUBBING
VHS
DVD
VHS
DUBBING indicator
[1]
While both DVD/VHS are stopped,
Press and hold [VHS
—, DUBBING] for
3 seconds or more.
≥Check if dubbing starts properly.
≥On the main unit, press [VHS —].
≥The “DUBBING” indicator on the main unit lights.
≥Dubbing is automatically completed when playback of the
disc is finished or the tape reaches to the end.
≥When dubbing is completed, a message indicating the
end of dubbing appears on the TV screen and then
disappears a few seconds later.
∫About Recording VISS
In One-Touch Dubbing from DVD to VHS, the index signal is
automatically recorded for each titles. You can search desired
titles with [
: ] or [ 9].
VHS
DVD
75VGN.book 60 ページ 2004年7月21日 水曜日 午前11時54分