La Crosse Technology WS-8025SU - Manual (Page 3)

REMOTE THERMO-SENSOR 433 MHz
TIME DATE WWWB
SUNRISE MOON PHASE
SUNSET INDOOR TEMPERATURE
TENDENCY
PRESSURE rel inHg PRESSURE HISTORY
OUTDOOR TEMPERATURE
LO MIN HI MAX
HUMIDITY LOCATION MOONSET
MOONRISE +1
PM PM
MIN MAX
RH %
HUMIDITY RH %
01
+7 +5 +3 +1 0 -1 -3 -5 -7 -1h -3h -6h -9h -12h -18h -24h -30h 0 +0.2 +0.5 +1 +2 +4
% RH % RH
2
R A D I O C O N T R O L L E D
IN
OUT
ALARM
SET
SUN/ MOON
CH
+
–
GB P.2 GB P.3
INVENTORY OF CONTENTS
1. WS-8025SU-indoor weather station
2. TX4U-remote thermo/hygro (temperature/humidity) sensor
3. Instruction manual and warranty card
ADDITIONAL EQUIPMENT (not included)
1. Five fresh AA 1.5V alkaline batteries.
2. One wall-mounting screw (optional)
ABOUT WWVB (radio-controlled time)
The NIST (National Institute of Standards and Technology-Time and Frequency Division) radio station,
WWVB, is located in Ft. Collins, Colorado and transmits the exact time signal continuously throughout
the United States at 60 kHz. The signal can be received up to 2,000 miles away through the internal
antenna in the indoor weather station. However, due to the nature of the Earth's Ionosphere, reception
is very limited during daylight hours. The indoor weather station will search for a signal every night
when reception is best. The WWVB radio station derives its signal from the NIST Atomic clock in
Boulder, Colorado. A team of atomic physicists continually measure every second of every day to an
accuracy of ten billionths of a second a day. These physicists have created an international standard,
measuring a second as 9,192,631,770 vibrations of a Cesium 133 atom in a vacuum. For more
information about WWVB please see the NIST website at
http://www.boulder.nist.gov/timefreq/stations/wwvb.htm
QUICK SET-UP GUIDE
Hint : Use good quality Alkaline Batteries and avoid rechargeable batteries.
1. Have the indoor weather station and remote thermo/hygro sensor 3 to 5 apart.
2. Batteries should be out of both units for 10 minutes.
3. Place the batteries into the remote thermo/hygro sensor first then into the indoor weather station.
(All remote thermo/hygro sensors must be started before the indoor weather station)
4. DO NOT PRESS ANY BUTTONS FOR 10 MINUTES.
In this time the indoor weather station and remote thermo/hygro sensor will start to talk to each other
and the indoor weather station will show both the indoor temperature and humidity and the outdoor
temperature and humidity. If the indoor weather station does not display all values after the 10
minutes please retry the set up as stated above. After all values are displayed for 10 minutes you can
place your remote thermo/hygro sensor outdoors and set your time.
The remote thermo/hygro sensor should be placed in a dry, shaded area. The remote thermo/hygro
sensor has a range of 200 feet. Any walls that the signal will have to pass through will reduce distance.
An outdoor wall or window will have 20 to 30 feet of resistance and an interior wall will have 10 to 20
feet of resistance. Your distance plus resistance should not exceed 200 ft. in a straight line.
TABLE OF CONTENTS
Topic Page
Inventory of Contents/ Additional Equipment 3
About WWVB 3
Quick Set Up Guide 3
Detailed Set Up Guide
Battery Installation 4
Start Up Sequence 5
Explanation of LCD Information 6
Function Key Layout 6
Program Mode 6
Time, 12/24 Hour Mode and Date Setting 7
City Location Setting 7
U.S. City Codes 8
Canada City Codes 11
Mexico City Codes 11
Time Zone and Daylight Saving Time (DST) Setting 11
Weather Measuring Units 11
LCD Contrast 12
Features and Operation
Sun Rise/Set and Moon Rise/Set Calculation 12
Moon Phase 13
Minimum/Maximum Temperature/Humidity 14
Multiple Remote Transmitters 14
Remote Temperature Alarm 15
Comfort Indicator 15
Weather Forecast Icon and Pressure Trend 15
Weather Tendency Arrows 16
Storm Warning Alarm 16
Two Hour Air Pressure Tendency Chart 17
Barometric Air Pressure Reading 17
Air Pressure History Bar Chart 17
Mounting 17
Maintenance and Care 19
Troubleshooting Guide 19
Specifications 19
Warranty Information 20