Lenovo 6528 User Manual
Page 6
Power and signal cables for internal drives
. . . . . . . . . . . . . . . . . . . . . . 55
Installing an adapter . . . . . . . . . . . . . . . . . . . . . . . 57
Removing a PCI card
. . . . . . . . . . . . . . . . . . . . . . 59
Installing a PCI card . . . . . . . . . . . . . . . . . . . . . . . 60
Removing a USB embedded hypervisor flash device . . . . . . . . . . . 61
Installing a USB embedded hypervisor flash device
Removing the virtual media key. . . . . . . . . . . . . . . . . . . 62
Installing the virtual media key . . . . . . . . . . . . . . . . . . . 63
Removing a hot-swap power supply . . . . . . . . . . . . . . . . . 64
Installing a hot-swap power supply
. . . . . . . . . . . . . . . . . 65
Installing a security rope clip . . . . . . . . . . . . . . . . . . . . 66
Completing the installation. . . . . . . . . . . . . . . . . . . . . 67
Reinstalling the two-piece bezel. . . . . . . . . . . . . . . . . . 67
Reinstalling the side cover. . . . . . . . . . . . . . . . . . . . 70
Connecting the cables . . . . . . . . . . . . . . . . . . . . . 71
Updating the server configuration . . . . . . . . . . . . . . . . . 71
Connecting external devices . . . . . . . . . . . . . . . . . . . . 71
Chapter 6. Installing and replacing customer replaceable units
Removing the rear system fan . . . . . . . . . . . . . . . . . . . 73
Installing the rear system fan. . . . . . . . . . . . . . . . . . . . 74
Removing the hard disk drive fan assembly . . . . . . . . . . . . . . 75
Installing the hard disk drive fan assembly . . . . . . . . . . . . . . . 76
Removing the simple-swap backplate
. . . . . . . . . . . . . . . . 78
Installing the simple-swap backplate . . . . . . . . . . . . . . . . . 79
Removing the SAS/SATA hard disk drive backplane . . . . . . . . . . . 81
Installing the SAS/SATA hard disk drive backplane . . . . . . . . . . . . 82
Removing the front-panel assembly . . . . . . . . . . . . . . . . . 83
Installing the front-panel assembly . . . . . . . . . . . . . . . . . . 83
Removing the front USB connector assembly. . . . . . . . . . . . . . 84
Installing the front USB connector assembly . . . . . . . . . . . . . . 85
Removing the rear adapter retention bracket . . . . . . . . . . . . . . 86
Installing the rear adapter retention bracket . . . . . . . . . . . . . . 86
Removing the front adapter-retention bracket . . . . . . . . . . . . . . 87
Installing the front adapter-retention bracket . . . . . . . . . . . . . . 87
Removing the hot-swap power supply cage . . . . . . . . . . . . . . 87
Installing the hot-swap power supply cage . . . . . . . . . . . . . . . 88
Removing the battery
. . . . . . . . . . . . . . . . . . . . . . 89
Installing the battery . . . . . . . . . . . . . . . . . . . . . . . 89
Removing and replacing FRUs . . . . . . . . . . . . . . . . . . . 90
Removing a ServeRAID BR10-il controller . . . . . . . . . . . . . . 91
Installing a ServeRAID BR10-il controller . . . . . . . . . . . . . . 91
Removing an optional ServeRAID-MR10i SAS/SATA controller . . . . . . 92
Installing an optional ServeRAID-MR10i SAS/SATA controller . . . . . . . 92
Removing an optional ServeRAID-MR10is VAULT SAS/SATA controller . . . 94
Installing an optional ServeRAID-MR10is VAULT SAS/SATA Controller . . . 94
Removing a non-hot-swap power supply
. . . . . . . . . . . . . . 96
Installing a non-hot-swap power supply . . . . . . . . . . . . . . . 98
Removing the microprocessor and fan sink
Installing a microprocessor and fan sink . . . . . . . . . . . . . . 101
Removing the system board
. . . . . . . . . . . . . . . . . . 104
Installing the system board . . . . . . . . . . . . . . . . . . . 106
Chapter 7. Configuring the server. . . . . . . . . . . . . . . . . 109
Using the Setup Utility . . . . . . . . . . . . . . . . . . . . . . 110
iv
ThinkServer TS200 Types 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530: Installation and User Guide