Land Pride RCR2560 - Manual (Page 15)

Revision Comments Part Description Part No. Ref.
Drawing Image Number dwg15881
(S/N 232953-) SHIELD WELDMENT 312-399H 1.
WASHER FLAT 3/8 SAE PLT 804-012C 2.
NUT WING 3/8-16 PLT 803-231C 3.
WASHER LOCK SPRING 3/8 PLT 804-013C 4.
Used on Omni Gearbox only FLAT WASHER 1 SPECIAL 804-070C 5.
Used on Comer Gearbox only CO BLANK WASHER 0.139.7101.00 5.
Rev. 1 Comer Box (SN 381566+) GBOX RC25 1.38-6 1:1.21 STD. 826-377C 6.
Rev. 2 Omni Box (SN 381565-) GEARBOX RC61SS 1:1.21 INCREASE 826-038C 6.
HHCS 5/16-18X1 GR5 802-159C 7.
NUT HEX FLG TOP LK 3/4-10 PLT 803-299C 8.
(S/N 220346-) GEARBOX SHAFT PROTECTOR 817-050C 9.
WASHER FLAT 5/16 SAE PLT 804-036C 10.
WASHER LOCK SPRING 5/16 PLT 804-009C 11.
(S/N 232953-) SHIELD MOUNT BRACKET WELDMENT 312-400H 12.
(S/N 584255+) RCR2684 DECK 326-114H 13.
RCR2684 DECK ORANGE 326-114H82 13.
(S/N 584254-) RCR2584 DECK WELDMENT 312-419H 13.
RCR25/2684 DECK WMT ORANGE 312-419H82 13.
NUT LOCK 3/8-16 PLT 803-013C 14.
PLOW 3/8-16X1 GR5 802-603C 15.
NUT HEX TOP LOCK 1 1/8-12 PLT. 803-170C 16.
WASHER FLAT 1 1/8 HARD ASTMF436 PN 804-147C 17.
Used with Omni or Comer Box 27 DISHPAN WLDMT LG.HUB 312-818H 18.
Standard (Quantity 2 per cutter) CUTTER BLADE 1/2 X 4 X 31 CCW 820-138C 19.
Optional Low Lift Blade (Quantity 2
per cutter) CUTTER BLADE 1/2X4X31 LL CCW 820-194C 19.
BLADE BOL 1 1/8-12X3 7/16 W/KY 802-277C 20.
Used on Omni Gearbox only NUT HEX SLOTTED 1-14 803-095C 21.
Used on Comer Gearbox only CO NUT, CASTLE M30 X 2 8.2.2.00555 21.
PIN COTTER 3/16 X 1 3/4 PLT 805-017C 22.
(S/N 584255+) PIN HITCH CAT. II - III 326-204D 23.
(S/N 584254-) HITCH PIN 300-236D 23.
PIN LYNCH 7/16 X 1 3/4 805-103C 24.
S/N 627945- ACCESS COVER PLATE 312-812D 25.
RPBY 312-812D 312-611D 25.
SKID SHOE 312-602D 26.
(S/N 558465+) HHCS 3/4-10X2 1/4 GR5 802-065C 27.
(S/N 558464-) HHCS 3/4-10X2 GR5 802-064C 27.
As Required S/N 776426- BLADE SPACER 16 GA .06 THICK 312-075D 28.
As Required S/N 776426- BLADE SPACER 18 GA .05 THICK 312-082D 28.
As Required S/N 776426- BLADE SPACER 20 GA .04 THICK 312-089D 28.
As Required S/N 776426- BLADE SPACER 24 GA .03 THICK 312-808D 28.
(S/N 640069+) LARGE SHAFT CONE W ACCESS DOOR 826-648C 29.
(S/N 640068-) RPBY 826-648C 826-222C 29.
HHCS 5/16-18X3/4 GR5 802-007C 30.
WASHER FLAT 5/16 USS PLT 804-010C 31.
Used on RCR2684 S/N 538584+ HHCS 1/4-20X1 1/4 GR5 802-224C 32.
Used on RCR2684 S/N 538584+ MANUAL STORAGE CONTAINER 816-504C 33.
Used on RCR2684 S/N 538584+ WASHER FLAT 1/4 SAE PLT 804-007C 34.
Used on RCR2684 S/N 538584+ NUT HEX NYLOCK 1/4-20 803-255C 35.
3-Point Mount PTO CAT. 4 X 43.7 SLIP CLUTCH 826-150C 36.
Pull Type PTO CAT. 4 X 20.5 FIXED 540 826-151C 37.
Pull Type PTO CAT. 4 X 49.21 JACKSHAFT 826-152C 38.
S/N 627946+ PLUG LP 3" ID RUBBER 840-273C 39.
01/14/13 RCR2560, RCR2572, RCR2584 & RCR2684 Rotary Cutter 312-459P 15
Table of Contents Part Number Index
Section 2: Decks Land Pride
Deck
Applies to RCR2584, RCR2684