Kawasaki 840074-1HR User Manual
Page 12
T
TO
O C
CH
HA
AN
NG
GE
E L
LA
AS
SE
ER
R B
BA
AT
TT
TE
ER
RIIE
ES
S::
1. Open battery compartment cover.
2. Make sure batteries are correctly positioned accord-
ing to the positive/negative markings on the compart-
ment.
3. Close cover.
O
OP
PE
ER
RA
AT
TIIN
NG
G T
TH
HE
E C
CIIR
RC
CU
UL
LA
AR
R S
SA
AW
W
B
Be
e a
aw
wa
arre
e tth
ha
att tth
hiiss tto
oo
oll iiss a
allw
wa
ayyss iin
n a
an
n o
op
pe
erra
attiin
ng
g cco
on
nd
diittiio
on
n
b
be
ecca
au
usse
e iitt d
do
oe
ess n
no
ott h
ha
avve
e tto
o b
be
e p
pllu
ug
gg
ge
ed
d iin
ntto
o a
an
n e
elle
eccttrriicca
all o
ou
uttlle
ett.. Always turn
the switch “
“O
OF
FF
F”
” and remove the battery pack before changing bits.
O
OP
PE
ER
RA
AT
TIIN
NG
G T
TH
HE
E T
TR
RIIG
GG
GE
ER
R S
SW
WIIT
TC
CH
H
N
Ne
evve
err tta
ap
pe
e tth
he
e ttrriig
gg
ge
err ssw
wiittcch
h d
do
ow
wn
n tto
o p
prro
ovviid
de
e
cco
on
nttiin
nu
uo
ou
uss h
hiig
gh
h ssp
pe
ee
ed
d.. The tool may fail under such conditions causing fire
or personal injury.
T
Th
he
e llo
occkk--o
offff b
bu
utttto
on
n h
he
ellp
pss p
prre
evve
en
ntt a
acccciid
de
en
ntta
all sstta
arrttiin
ng
g..
This button can be pressed from either side.
T
TH
HIIS
S T
TO
OO
OL
L IIS
S C
CO
ON
NT
TR
RO
OL
LL
LE
ED
D B
BY
Y
A
A T
TR
RIIG
GG
GE
ER
R S
SW
WIIT
TC
CH
H::
Press the lock-off button, then
pull the “
“O
ON
N//O
OF
FF
F”
” trigger to turn
the Circular Saw “
“O
ON
N”
”.
To turn the Circular Saw “
“O
OF
FF
F”
”,
release the trigger switch. The
lock-off button will automatically
reset.
22
• Mark the desired line of cut so it is easily visible.
• Set the shoe against the work piece.
• Push laser “
“O
ON
N//O
OF
FF
F”
” switch to “
“O
ON
N”
”.
• Adjust the laser line until it lines up with the cut line marking. Blade will now be
in the proper position to make your cut.
• Pull the trigger to start the saw.
• When the blade reaches full speed, slowly feed the blade into the work piece.
When the blade starts cutting, release the blade guard.
• D
DO
O N
NO
OT
T force saw. Allow saw to cut at its own rate.
• Cut straight lines only. Attempting to cut a curve will bend the blade which could
result in personal injury or damage to the tool.
• If you need to stop in the middle of a cut, turn off the saw and allow it to come
to a complete stop before removing it from the material.
• When the cut is finished, turn off the laser light.
R
RE
EP
PL
LA
AC
CIIN
NG
G L
LA
AS
SE
ER
R B
BA
AT
TT
TE
ER
RIIE
ES
S
The laser runs on two AAA batteries which are located beneath the “
“O
ON
N//O
OF
FF
F”
”
switch.
When the laser light begins to dim, change both batteries.
Remove batteries before putting the circular saw into storage. Batteries may leak
and cause damage if the laser is not used for over 90 days.
21
TRIGGER
LASER ON/OFF SWITCH
PENCIL LINE
LASER LINE
CAUTION LABEL
LOCK-OFF BUTTON
TRIGGER
SWITCH