Kawasaki 840074-1HR User Manual
Page 11
N
NE
EV
VE
ER
R O
OP
PE
ER
RA
AT
TE
E L
LA
AS
SE
ER
R IIF
F T
TH
HE
E U
UN
NIIT
T IIS
S D
DE
EF
FE
EC
CT
TIIV
VE
E O
OR
R T
TH
HE
E C
CO
OV
VE
ER
R O
OR
R S
SE
EA
AL
L
IIS
S D
DA
AM
MA
AG
GE
ED
D..
D
DO
O N
NO
OT
T S
SE
ER
RV
VIIC
CE
E L
LA
AS
SE
ER
R.. The laser unit must be returned to the factory for any
service or repair. Service or repair must be handled by authorized factory
trained technicians.
Do not open the laser unit except to change batteries.
R
RE
EM
MO
OV
VE
E B
BA
AT
TT
TE
ER
RIIE
ES
S IIF
F T
TH
HE
E L
LE
EV
VE
EL
L IIS
S T
TO
O B
BE
E S
ST
TO
OR
RE
ED
D F
FO
OR
R A
AN
NY
Y L
LE
EN
NG
GT
TH
H O
OF
F
T
TIIM
ME
E.. Batteries may leak and damage the laser if it is stored idle for more than
3 months.
Be careful with this tool. Striking or jarring it, especially on the laser housing,
can affect its accuracy.
Other than batteries, there are no user-serviceable parts in the laser device.
U
US
SIIN
NG
G T
TH
HE
E L
LA
AS
SE
ER
R
U
Usse
e o
off cco
on
nttrro
ollss o
orr a
ad
djju
ussttm
me
en
nttss o
orr p
pe
errffo
orrm
ma
an
ncce
e o
off p
prro
occe
e--
d
du
urre
ess o
otth
he
err tth
ha
an
n tth
ho
osse
e ssp
pe
ecciiffiie
ed
d h
he
erre
eiin
n m
ma
ayy rre
essu
ulltt iin
n h
ha
azza
arrd
do
ou
uss rra
ad
diia
attiio
on
n
e
exxp
po
ossu
urre
e..
S
Sh
ha
arrp
p b
bllo
ow
wss m
ma
ayy a
affffe
ecctt tth
he
e a
accccu
urra
accyy o
off tth
hiiss lla
asse
err.. Avoid
striking the laser housing.
A
AD
DJJU
US
ST
T B
BE
EV
VE
EL
L A
AN
NG
GL
LE
E::
1. Remove the battery pack.
2. Loosen the bevel angle knob by
turning it counter-clockwise.
3. Adjust the angle of your cut.
4. Tighten the angle knob securely
by turning clockwise.
L
LA
AS
SE
ER
R G
GU
UIID
DE
E
Use of controls or procedures, or performance of proce-
dures other then those specified herein may result in hazardous radiation
exposure.
L
LA
AS
SE
ER
R S
SA
AF
FE
ET
TY
Y
N
NE
EV
VE
ER
R L
LO
OO
OK
K IIN
NT
TO
O T
TH
HE
E L
LA
AS
SE
ER
R B
BE
EA
AM
M.. Any contact with the eyes by the beam
could cause injury. Do not use the laser when cutting reflective materials.
D
DO
O N
NO
OT
T A
AIIM
M T
TH
HE
E L
LA
AS
SE
ER
R B
BE
EA
AM
M A
AT
T A
AN
NY
YO
ON
NE
E O
OR
R A
AT
T R
RE
EF
FL
LE
EC
CT
TIIV
VE
E S
SU
UR
RF
FA
AC
CE
ES
S..
C
CL
LA
AS
SS
S 2
2M
M L
LA
AS
SE
ER
R P
PR
RO
OD
DU
UC
CT
T.. Any contact with the eyes by the beam could
cause injury. Ensure the laser beam is turned on only when the tool is on a non-
reflective workpiece and as such it is aimed only at the work surface. Metals and
other materials like steel which can be highly reflective should only be cut with-
out the use of the laser.
S
ST
TO
OR
RE
E O
OU
UT
T O
OF
F R
RE
EA
AC
CH
H O
OF
F C
CH
HIIL
LD
DR
RE
EN
N.. Equipment should be in a high location
or locked up to keep out of reach of children. It is not a toy.
D
DO
O N
NO
OT
T T
TA
AM
MP
PE
ER
R W
WIIT
TH
H T
TH
HE
E L
LA
AS
SE
ER
R O
OU
UT
TP
PU
UT
T.. Changing the performance of the
laser to increase its output is prohibited. Any claim for damages or injuries
resulting from not following these instructions will be refused.
O
OP
PE
ER
RA
AT
TIIO
ON
N A
AC
CC
CE
ES
SS
SIIB
BL
LE
E F
FIIE
EL
LD
DS
S::
Wavelength
636-660nm
Laser Power for Classification
<1mW CW
19
20
45º
BEVEL
ANGLE
KNOB
LASER LIGHT
DO NOT VIEW DIRECTLY WITH OPTICAL
INSTRUMENTS (MAGNIFIERS)
CLASS 2M LASER PRODUCT
635-660nm, <1mW CW
CLASSIFIEDS PER IEC 60825-1, Ed. 1.2, 2001-08
AVOID EXPOSURE -
LASER LIGHT IS
EMITTED FROM THIS APERTURE.”
LASER RADIATION
CAUTION LABEL