Kawasaki 840074-1HR User Manual
Page 10
A
AD
DJJU
US
ST
TIIN
NG
G D
DE
EP
PT
TH
H A
AN
ND
D A
AN
NG
GL
LE
E
A
AD
DJJU
US
ST
T C
CU
UT
TT
TIIN
NG
G D
DE
EP
PT
TH
H::
1. Remove the battery pack.
2. Hold the saw firmly and loosen the
depth adjustment knob by turning
it counter-clockwise.
3. Move the shoe to obtain the desired
depth of cut.
4. Tighten depth adjustment knob
securely by turning clockwise
before operating the saw.
4. After approximately one hour of charging, the red indicator light should go
“
“O
OF
FF
F”
” and the green light should come “
“O
ON
N”
”. The green light indicates that the
battery is fully charged.
5. When fully charged, reattach battery pack onto Cordless Circular Saw, making
certain latches fasten securely. Cordless Circular Saw will not operate properly if
the battery pack is not seated properly.
A
AS
SS
SE
EM
MB
BL
LY
Y
A
Allw
wa
ayyss rre
em
mo
ovve
e b
ba
atttte
erryy p
pa
acckk b
be
effo
orre
e iin
nsstta
alllliin
ng
g o
orr rre
em
mo
ovviin
ng
g b
blla
ad
de
e..
W
Wh
he
en
n rre
em
mo
ovviin
ng
g tth
he
e b
blla
ad
de
e ffrro
om
m tth
he
e tto
oo
oll,, a
avvo
oiid
d cco
on
ntta
acctt w
wiitth
h sskkiin
n a
an
nd
d u
usse
e
p
prro
op
pe
err p
prro
otte
eccttiivve
e g
gllo
ovve
ess w
wh
he
en
n g
grra
assp
piin
ng
g tth
he
e b
blla
ad
de
e o
orr a
acccce
esssso
orryy.. Accessories
may be hot after prolonged use.
If the blade clamp screw will not loosen enough to allow
blade installation, tap gently on the end of the wrench with a mallet until the
clamp screw breaks free.
A
AT
TT
TA
AC
CH
HIIN
NG
G // R
RE
EM
MO
OV
VIIN
NG
G B
BL
LA
AD
DE
E
A
AT
TT
TA
AC
CH
HIIN
NG
G T
TH
HE
E B
BL
LA
AD
DE
E::
1. Remove the battery pack.
2. Retract the lower guard (see Fig. 1).
3. Slip the blade into place (see Fig. 2).
4. Put clamp washers and clamping
screw loosely in position.
5. Use the wrench to tighten the
clamping screw while pressing
down on the clamping knob
(see Fig. 3 and Fig. 4).
6. Remove wrench.
7. Replace the battery pack.
17
DEPTH
ADJUSTMENT
KNOB
18
R
RE
EM
MO
OV
VIIN
NG
G T
TH
HE
E B
BL
LA
AD
DE
E::
1. Remove the battery pack.
2. Use the wrench to loosen the
clamping screw while pressing
down on the blade safety lock
button (see Fig. 3 and Fig. 4).
3. Remove the blade.
4. Tighten the blade clamp
screw back into place.
5. Remove wrench.
6. Replace the battery pack.
FIG. 1
FIG. 2
FIG. 3
FIG. 4
L
LO
OO
OS
SE
EN
N::
CLOCKWISE
T
TIIG
GH
HT
TE
EN
N::
COUNTER-
CLOCKWISE