Scag Power Equipment STWC - Manual (Page 43)

39
Section 8
1 461656 Cutter Deck Advantage
2 04003-04 Bolt, Carr. 5/16-18 x 1”
3 04019-04 Nut, 3/8-16 Serrated Flange
4 481625-01 Wing Nut, 3/8-16
5 481632 Anti-Scalp Wheel
6 04003-26 Bolt, Carriage 3/8-16 x 4”
7 422478 Bracket, Anti-Scalp Wheel
8 04017-27 Bolt, Serrated Flange 3/8-16 x 1”
9 04043-06 Flatwasher, 5/8” Hardened
10 04021-05 Locknut, 3/8-16 Center Lock
11 461296 Discharge Chute
12 04001-11 Bolt, Hex Head 5/16-18 x 1-1/2”, Rear
04001-12 Bolt, Hex Head 5/16-18 x 1-3/4”, Front
13 04021-10 Nut, Elastic Stop 5/16-18
14 04020-09 Nut, 5/8-11 UNC
15 45944 Shaft, Roller
16 04001-41 Bolt, Hex Head 5/8-11 x 9-1/2”
17 48038 Roller, Rear
18 04001-154 Bolt, Hex Head 5/16-18 x 4-3/4”
19 04063-08 Key, 1/4 x 1/4 x 2”
20 482718 Spring, Idler
21 04043-04 Flatwasher, 3/8” - .938 x .391 x .105
22 04001-176 Bolt, Hex Head 5/16-18 x 1-3/4” Grade 8
23 04019-03 Nut, Serrated Flange 5/16-18
24 04001-172 Bolt, Hex Head 1/4-20 x 1” Grade 8
25 48100-15 Bushing, .376 ID Oilite
26 04030-03 Lockwasher 5/16”
27 04040-15 Flatwasher 5/16”
28 04001-136 Bolt, 3/8-16 x 1-1/2” Grade 8
29 04021-09 Nut, Elastic Stop 3/8-16
30 04001-31 Bolt, Hex Head 3/8-16 x 2-1/2”
31 04001-54 Bolt, Hex Head 3/8-16 x 3”
32 04001-136 Bolt, Hex Head 3/8-16 x 1-1/2 Grade 8
33 04110-03 U-Nut, 3/8-16
34 461663 Spindle Assembly
35 43589 Shaft, Spindle
36 481024 Seal Upper
37 481022 Bearing Assembly
38 48114-04 Grease Fitting
39 48677 Valve, Grease Relief
40 43644 Housing, Spindle
41 43312 Spacer, Outside
42 43296 Spacer, Inside
61A" CUTTER DECK
43 481025 Seal, Lower
44 43297 Bushing, Bottom
45 481035 Nut, Special 1-1/16 - 18
46 43590 Spacer, Spindle
47 481708 Cutter Blade 21”
48 422713 Pivot, Idler Base
49 48224 Bearing
50 461174 Idler Arm Assy.
51 43575 Idler Pivot, Short
52 423717 Belt Cover (61A)
53 48926 Hub, Tapered 1-1/8” Bore
54 482416 Pulley, Idler 5.0”
55 04001-14 Bolt, Hex Head 1/4-20 x 1”
56 482648 Pulley, 5.95 Dia. Tapered Bore
57 423880 Turbo Baffle, Bolt On
58 451240 Push Arm Shaft
59 461516 Push Arm (Includes 64,60,62)
60 04020-16 Nut, 5/8-18 UNF
61 04021-13 Nut, Elastic Stop 5/8-11
62 48763 Rod End, 5/8 Male RH Thread
63 04001-79 Bolt, Hex Head 5/8-11 x 4-1/2”
64 48114-04 Grease Fitting, 90 Degree
65 482652 Belt, Cutter Deck Drive (61A)
66 04001-09 Bolt, Hex Head 5/16-18 x 1”
67 482245 Spring, Discharge Chute
68 423792 Baffle Weldment, 61A
69 04003-23 Bolt, Carriage 3/8-16 x 1”
70 04041-07 Flatwasher, 3/8-.391 x .938 x .105
71 04001-51 Bolt, Hex Head 3/8-16 x 3-3/4”
72 482743 Pulley, Idler 5.0” OD
73 482295 Wheel, Anti Scalp
74 45944 Roller Shaft
Ref. Part
No. No.
Description
Ref. Part
No. No.
Description