Sherwood R-956 - Manual (Page 14)

1 4
L I S T E N I N G T O A P R O G R A M
Operations
Before operation
Select the desired input source.
3
Enter the standby mode.
The STANDBY button lights up in red.
This means that the receiver is connected to the AC
mains and a small amount of current is retained to
support the memorized contents and operation
readiness.
To switch the power completely off, push the
POWER switch again.
The power is cut off and the STANDBY light goes
off.
Each time the STANDBY button on the front panel or
the POWER button on the remote control is pressed,
the receiver turns on to enter the operating mode(the
STANDBY button lights up in green) or turns off to
enter the standby mode (the STANDBY button lights
up in red).
In the standby mode, if one of the INPUT
SELECTOR buttons is pressed, the receiver turns on
automatically and the desired input is selected.
The SPEAKER indicator lights up on the display and
sound can be heard from the speakers connected to the
speaker terminals.
When using headphones for private listening, press the
SPEAKER button again to switch the speakers off.
Each time the “AUDIO” button is pressed, the input
source changes as follows;
PHONO TUNER CD PLAYER AUX
(frequency display)
Each time the “VIDEO” or “VID SEL” button is
pressed, the input source changes as follows;
VIDEO 1 VIDEO 2 ----- VIDEO 5
When the TAPE MONITOR button is set to ON so
that “TAPE MON” lights up, other inputs can not be
heard from the speakers.
To listen to an input source other than TAPE MONITOR,
be sure to set the TAPE MONITOR button to off.
TAPE MONITOR function
You can connect either a tape deck or a graphic equalizer
to the receiver’s TAPE MONITOR jacks.
To listen to the component connected to these jacks, set the
TAPE MONITOR button to on.
If you connect a 3-head tape deck, you can monitor the
actual recording, not the source sound.
For further details, refer to the operating instructions of
the component connected.
When selecting the 6.1 CH DIRECT as desired
6.1 CH DIRECT is displayed and the 7 separate
analog signals from a decoder or DVD player
connected to this unit will be heard. You can use the
tone controls and volume control to adjust the signal.
(If the TAPE MONITOR button is to on, it will
automatically be set to off.)
To cancel the 6.1 CH direct function, press the 6.1 CH
DIRECT button again or select the desired input
source.
These 7 separate analog signals can be heard, only.
They cannot be recorded.
In the standby mode, turn the power on.
1
Switch the speakers on.
2
ENGLISH
MAIN POWER
ON / OFF
or
INPUT SELECTOR
AUDIO VIDEO TAPE MON.
SE TUP
AUD
SAT
VOL
VID 4
SE TUP
P.SCAN
VOL SLEEP CH LEVL
HOME THEATER MASTER RNC-30
PWR
ENTER
PHONO CD TUNER TAPE MON
T2 MON VID SEL VID 2 VID 3
VID 4 AUX ROOM 2 SYS DISP
AUD CD DVD AUX
TV VCR CBL SAT
1 2 3
4 5 6
7 8 9
MUTE 0 CH SEL
T.TONE
D.TIME D.ADJ
STEREO AUTO
6.1CH IN DSP MODE
OSD
AUX CD TUNER PHONO TAPE MON
VID SEL
AUX
ON/STANDBY
STANDBY
or
SE TUP
AUD
SAT
VOL
VID 4
SE TUP
P.SCAN
VOL SLEEP CH LEVL
HOME THEATER MASTER RNC-30
PWR
ENTER
PHONO CD TUNER TAPE MON
T2 MON VID SEL VID 2 VID 3
VID 4 AUX ROOM 2 SYS DISP
AUD CD DVD AUX
TV VCR CBL SAT
1 2 3
4 5 6
7 8 9
MUTE 0 CH SEL
T.TONE
D.TIME D.ADJ
STEREO AUTO
6.1CH IN C.MODE DSP MODE
OSD
PWR
ON/OFF
SPEAKER
or
6.1CH DIRECT
SE TUP
AUD
SAT
VOL
VID 4
SE TUP
P.SCAN
VOL SLEEP CH LEVL
HOME THEATER MASTER RNC-30
PWR
ENTER
PHONO CD TUNER TAPE MON
T2 MON VID SEL VID 2 VID 3
VID 4 AUX ROOM 2 SYS DISP
AUD CD DVD AUX
TV VCR CBL SAT
1 2 3
4 5 6
7 8 9
MUTE 0 CH SEL
T.TONE
D.TIME D.ADJ
STEREO AUTO
6.1CH IN DSP MODE
OSD 6.1CH IN
Note : Before operating this receiver with the supplied remote control, refer to “Universal Remote Control” on page 10 for
details about operation.