Shindaiwa 80045 - Manual (Page 4)

3. Feed control knob/wire through the
T-handle until the caution label
touches the round hole.
See Figure 3.
DO NOT COMPRESS THE
SPRING AT THIS TIME.
Feed the T-handle/control wire
assembly through the square
handle tube towards the locator
dot. See Figure 4. Secure the T-
handle to the tube with (2)1/4-20 x
2 1/4" bolts, (4) flat washers, and
(2) hex nuts. See Figure 3.
4. Turn the spreader upright and
install the handle tube with the dot
between the handle braces as
shown. Install (2) 1/4 x 1 1/2" hex
bolts and nuts. See Figure 4.
The feed control wire must be
positioned above the handle
brace bolts to operate properly.
Securely tighten all nuts and bolts
installed in previous steps.
1. Remove the spreader and compo-
nents from the carton and place the
spreader upside down on a padded
surface. Install the LH & RH handle
braces to frame using four 1/4-20 x
2 1/4" hex bolts and nuts. Do not
tighten at this time. See Figure 1.
2. Install drive wheel onto the right-
hand end of the axle as viewed
from the operating position. (You
can identify the drive wheel by the
cotter pin hole drilled in the hub).
The hub must face towards frame.
Align the hole in the drive wheel
hub and the hole in the axle.
Secure drive wheel to axle with the
5/32" x 2" cotter pin. Install the
free wheel on the opposite end of
the axle. Insert the 5/32" x 1"
cotter pin to retain the free wheel.
See Figure 2.
1/4-20 x 2"
Hex Bolt
1/4-20 Hex
Nut &
Washer
Handle
Tube
1/4-20
Hex Nut
2
Assembly
Figure 1
Figure 2
Figure 3
Figure 4
Dot
1/4-20 x 2 1/4
Hex Bolt
RH Handle
Brace
LH Handle
Brace
1/4-20
Hex Nut
5/32 x 1"
Cotter Pin
Drive
Wheel
Free
Wheel
5/32 x 2"
Cotter Pin
1/4-20 x
2 1/4"
Bolt
OFF ON
Shindaiwa Limited Warranty
Shindaiwa Inc. manufactures its
products to superior quality standards
to afford our customers the highest
level of satisfaction. In keeping with
this goal, Shindaiwa Inc. warrants this
HomePro
ீ 75RS Spreader to the
original purchaser as follows:
Warranty Period
Ⅵ 1 year for Personal/Consumer use.
Ⅵ 180 days for Commercial/
Institutional use.
Ⅵ 90 days for rental use.
Warranty Administration
Within the covered warranty
period, Shindaiwa Inc. will, at their
option, repair or replace any defect in
material or workmanship, without
charge for parts or labor, if this
product is presented at an authorized
Shindaiwa dealer.
Warranty Exclusions
and Limitations
Shindaiwa Inc. assumes no responsi-
bility for damages, loss, or injury
resulting from:
Ⅵ Normal wear and tear.
Ⅵ Misuse or neglect.
Ⅵ Modification to or removal of
original component parts.
This warranty is limited to the terms
stated herein. Shindaiwa Inc. dis-
claims all liability for incidental or
consequential damages. Some states
do not allow the exclusion of inciden-
tal or consequential damages, so these
limitations may not apply to you.
This warranty gives you specific
legal rights, and you may also have
other rights which may vary from
state to state.
Shindaiwa Inc. reserves the right to
change the design or specifications of
this product without obligation to
modify previously manufactured
products.
Owner’s Responsibilities.
The owner of this product shall
demonstrate reasonable care in the
use, maintenance, and storage of this
Shindaiwa product. If a warrantable
failure should occur, the owner shall
deliver the product to an authorized
Shindaiwa servicing dealer for
correction.
To obtain warranty service, proof of
purchase must be presented to the
authorized Shindaiwa servicing dealer
when the product is presented for
repairs.
Proof of purchase must include
date of purchase and the name and
address of the selling dealer.
11