Sun Microsystems STOREDGE FC-100 User Manual

Storedge, Fc-100 hub installation and service manual, Formerly the sun

Table of contents

Document Outline

Sun™ StorEdge™ FC-100 Hub Installation and Service Manual
- Formerly the Sun™ Enterprise Network Array™
- Regulatory Compliance Statements
Declaration of Conformity
- EMC
  - European Union-EC
- Safety
- Supplementary Information
Contents
- 1. Product Description11
- 2. Installation21
- 3. Service31
- A. SpecificationsA1
  - Preface
Using UNIX Commands
Typographic Conventions
- TABLEP1 Typographic Conventions
Shell Prompts
- TABLEP2 Shell Prompts
Related Documentation
Sun Documentation on the Web
Sun Welcomes Your Comments
- 1
- Product Description
1.1 Sun StorEdge FC100 Hub
- FIGURE11 Front of Hub
- FIGURE12 Rear of Hub
1.2 GBIC
- FIGURE13 GBIC That Does Not Have a Bail
- FIGURE14 GBIC That Has a Bail
- 2
- Installation
2.1 Inspecting the Hub
- 1. Unpack the hub.
- 2. Inspect the hub for evidence of damage.
- 3. Save the packing materials for future use.
2.2 Rackmount Placement
2.3 Installing the Hub
- 2.3.1 Tools You Will Need
- 2.3.2 Preparing the Cabinet
- 2.3.3 Installing the Mounting Tray in the Cabinet
  - 1. Select the correct mounting holes in the cabinet to use for the tray.
  - 2. Install the tray in the cabinet (FIGURE21).
- 2.3.4 Installing the Hub on the Mounting Tray
  - 1. Determine on which side of the tray you are going to install the hub.
  - 2. From the rear of the tray, slide the hub mounting bracket into the slots in the mounting tray ...
    - FIGURE22 Installing the Hub on a Mounting Tray
- 2.3.5 Installing GBICs and Fiber Optic Cables
- 2.3.6 Routing the Power Cord
- 2.3.7 Verifying the Configuration
  - 1. Power on all nodes and then the hub.
  - 2. Make sure that the Device Active LEDs are lit for active hub ports.
- 2.3.8 Reassembling the Cabinet
2.4 Troubleshooting
- TABLE21 Troubleshooting
- 3
- Service
3.1 Installing a GBIC
- 1. Choose the hub port into which you will install the GBIC.
- 2. Insert the GBIC into the port.
  - FIGURE31 Installing a GBIC That Does Not Have a Bail
  - FIGURE32 Installing a GBIC That Has a Bail
- 3. Connect the fiber optic cable to the GBIC.
3.2 Removing a GBIC
- 1. Disconnect the fiber optic cable from the GBIC (FIGURE33 or FIGURE34).
- 2. Remove the GBIC.
  - FIGURE33 Removing a GBIC That Does Not Have a Bail
  - FIGURE34 Removing a GBIC That Has a Bail
3.3 Removing a Hub
- 1. Disconnect and remove any installed fiber optic cables or GBICs (FIGURE33).
- 2. Disconnect the AC power cord from the hub.
- 3. Push up on the retaining tab that secures the hub to the mounting tray (FIGURE35).
  - FIGURE35 Removing the Hub
- 4. Pull the hub back and then lift it out of the mounting slots.
- A
- Specifications
A.1 Physical
- TABLEA1 Physical Specifications
A.2 Electrical
- TABLEA2 Electrical Specifications
A.3 Environmental
- TABLEA3 Environmental Specifications