Siemens Gigaset 4000 - Manual (Page 2)

End key and On/Off key
BASIC PHONE OPERATION
Making a Call 1 Dial desired number.
2 Press .
3 Press or place handset in base
(or charger) to hang up.
Answering Call Lift handset from base (or charger)
or press .
Intercom Call 1 Lift handset.
2 Select INT, select the desired handset’s
intercom number, and press .
3 To call all handsets, select INT and
press « or press «, select INT, and
press .
4 Press or place handset in base
(or charger) to hang up.
Setting Volume 1 Open the Menu.
2 Scroll to “Handset Settings” and
press OK.
3 Select “Handset Volume” and press
OK.
You will hear the current volume in the
earpiece and its level is displayed. Scroll
to the desired volume and press OK.
Setting Language 1 Open the Menu.
2 Press ¬and then press Ÿ.
3 To select English (default),
press Þand ];
to select French, press Þand Ÿ;
to select Spanish, press Þand ^.
Paging Handset Press the page button on the base bottom.
LED
Lights up during a call;
flashes at:
-incoming calls
-new calls
-new messages
Headset
Jack
Talk key
-answer a call
-dial a telephone
number
Directory key
Open the directory
Key 1
(Programmable) Hold
down to select the
answering machine or
telephone company
voice mail
Star key (*)
Hold down to turn
on/off the ringer
Flash key
Hold key down to pause;
press to answer
waiting call
Your handset is now registered
and ready for use.
Charge status
Display screen
Current display
Soft keys
End key and
On/Off key
-end the call
-cancel function
-one menu level back
(press briefly)
-return to idle state
(hold down)
-when the telephone is
idle on/off (hold down)
Pound key (#)
Hold down to turn
on/off keypad
protection
Memory key
Microphone
Intercom telephone
number of the handset
Gigaset 4000 Handset
The handset included with the system is automatically registered with the
base station. Up to a total of four handsets (dependent on system) may be
added to any Gigaset 4010, 4015, 4210, or 4215 base.
Handset Setup
Before using your handset, follow these steps:
See User Manual for additional options.
Automatic Registration to Base Unit
1
Place handset in base with display facing out.
Note: DO NOT press the END
(On/Off) key before placing handset
in base. (If handset is on, turn it off.)
2
After approximately one minute,
handset will register to the base and
the next unassigned intercom
number (2 through 4) is automatically
assigned. The intercom number
appears in the upper left of the
handset display. The handset reverts
to the idle state.
3
Place handset in charger or base unit
with display facing out and follow
charging instructions as above.
IMPORTANT: Charge batteries 12 to 14 hours before using the
handset for the first time. WARNING: Use only NiCd or NiMh
“AA” rechargeable batteries. DO NOT USE ALKALINE, LITHIUM,
OR NON-RECHARGEABLE BATTERIES.
+
+
–
–
2
Insert batteries
as shown. 3
Place cover on back
of handset and push
gently upward
until it clicks
into place.
1
Remove protective
plastic film from display.
4
Place handset
in charger
with display
facing out.
Visite nuestro sitio Web para obtener instrucciones en español.
Customer Care: 1-888-777-0211
Or visit our Website: www.icm.siemens.com
Visite nuestro sitio Web para obtener instrucciones en español.
Customer Care: 1-888-777-0211
Or visit our Website: www.icm.siemens.com
Visite nuestro sitio Web para obtener instrucciones en español.
Customer Care: 1-888-777-0211
Or visit our Website: www.icm.siemens.com