JVC LPT0923-001B - Manual (Page 46)

Filename [DR-MH30EU_07Timer Recording.fm]
Masterpage:Left+
46
EN
TIMER RECORDING
Page 46 Tuesday, 29 June 2004 17:40
You can programme this unit to timer-record as many as
32 programmes.
If you do not know the S
HOW V IEW number for the programme you
wish to record, use the following procedure to set your unit to
timer-record the programme.
1
Load a recordable disc if recording to DVD.
2
Press PROGRAMME to access the programme top screen.
3
Press rtw e to select “CALENDAR PR.”, then press ENTER.
● When “PROGRAMME FULL DELETE UNWANTED TIMER
PROGRAMMES” appears on the TV screen, you need to cancel
some of the reserved programmes. (
੬ pg. 47)
4
Press rtw e to select the desired date, then press ENTER.
5
Press rt to select “RECORD
TO”, then press ENTER. Press
rt to select the desired
recording deck, then press
ENTER.
6
Press rt to select “START”, then press ENTER. Press rt to
set the desired start time, then press ENTER.
● Each press of rt advances/goes back the start time in 1-min.
increments.
● To advance/go back the start time in 30-min. increments, press and
hold rt.
7
Press rt to select “STOP”, then press ENTER. Press rt to
set the desired stop time, then press ENTER.
● Each press of rt advances/goes back the stop time in 1-min.
increments.
● To advance/go back the stop time in 30-min. increments, press and
hold rt.
8
Press rt to select “TV PROG”, then press ENTER. Press rt
to select the desired channel.
9
Press rt to select “CONFIRM”, then press ENTER.
10
Set the other recording options as required.
● Refer to step 8 in “ShowViewTM Timer Programming” ( ੬
pg. 44).
11
Press rt to select “OK”,
then press ENTER to access the
Programme Confirmation screen.
12
Press w e to select “EXIT”,
then press ENTER to complete
timer programming.
● To programme another timer,
press w e to select
“CONTINUE”, then press
ENTER.
● If “PROGRAMME OVERLAPPED” appears on the TV screen, see
page 47.
NOTES:
● When two successive programmes are recorded on a DVD-RW disc
with Manual Timer Programming function, the beginning of the
second one may be left off the recording.
● If the copy limited programme is received during timer-recording, the
unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you programmed.
Manual Timer Programming
● Make sure that the unit’s built-in clock is set properly.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
rtwe
AUX
PROGRAMME
ENTER
CABLE/SAT
DVD TV
14/01/04 WED 22:30 - 23:00 BBC1
[MISC. ] XP
PRESS [PROGRAMME]
TO EXIT
[0]: SAT
SELECT WITH [ ]
THEN PRESS [ENTER]
BBC1 TV PROG
23:00 STOP
22:30 START
HDD RECORD TO
PROGRAMME > CALENDAR PR. (2/3)
CONFIRM
ENTER
SELECT EXIT
PROGRAMME
2
Satellite Receiver Users
To timer-record a satellite broadcast using Manual Timer
Programming:
A Perform “Satellite Receiver Control Setting” (੬ pg. 23).
B Perform “Manual Timer Programming” (੬ pg. 46). In step 8,
press AUX to change “TV PROG” to “SAT”. Then press rt to
enter the channel position for the satellite broadcast.
C Leave the satellite receiver’s power on.
Relief Recording
When a programme that is set for the DVD deck cannot be
recorded properly, the programme is recorded to the HDD deck
instead in the same recording mode as set.
● If the remaining capacity of the hard disc is not sufficient, the
programme is recorded to the DVD deck until the remaining
capacity of the DVD disc lasts.
● If “JUST” is selected for the recording mode, the current recording
mode for the DVD deck is applied.
14/01/04 WED 22:30 - 23:00 BBC1
[EDUCATION] GARDENING FR360
1:00 28:00
ENTER
SELECT EXIT
SELECT WITH [ ]
THEN PRESS [ENTER]
MON-FRI (FOR A WEEK) WEEKLY/DAILY
OFF VPS/PDC
EDUCATION CATEGORY
GARDENING INPUT TITLE
PROGRAMME > CALENDAR PR. (3/3)
O K
FR360 REC MODE
PRESS [PROGRAMME]
TO EXIT
PROGRAMME
2
DR-MH30EU_00.book Page 46 Tuesday, June 29, 2004 5:41 PM