Recording features, Instant timer recording (itr), Receiving stereo and bilingual programmes – JVC LPT0923-001B User Manual
Page 39: Pg. 39) or t
Masterpage:Right+
EN
39
Filename [DR-MH30EU_06HDD Operation.fm]
BASIC OPERATIONS ON HDD DECK
Page 39
Tuesday, 29 June 2004 17:40
Instant Timer Recording (ITR)
This easy method lets you record for from 30 minutes to 6 hours
(selectable in 30-min. increments), and shuts the unit off after
recording is finished.
1
Press 7 on the unit to start recording.
2
Press 7 again to engage the ITR mode.
● On the front display panel, “0:30” appears.
3
If you want to record for more than 30 minutes, press 7 to
extend the time. Each press extends recording time by 30 minutes.
NOTES:
● You can only perform ITR using the 7 button on the unit.
● If “DIRECT REC” is set to “ON” in the menu, Instant Timer Recording
(ITR) function does not work. (
● When the recording capacity becomes full during timer recording or
Instant Timer Recording, the unit is automatically shut off.
Watch Another Programme While Recording On The
Unit
While recording is going on, you can watch another programme on
the TV by using the TV’s tuner.
NOTE:
It is required that the remote control is set to be able to operate the TV
in advance. (
1
During recording, press TV AV/VIDEO to select TV mode.
● Video mode is disengaged and the video lamp (VIDEO) on the unit is
turned off.
● The programme received on the TV’s tuner is displayed on the TV
screen.
2
Slide the TV/CABLE/SAT/DVD switch to TV.
3
Press PR +/– repeatedly to select the desired channel.
NOTE:
If a decoder is connected to the unit (
pg. 66), you can select a
scrambled channel as well as other normal channels.
Elapsed Recording Time And Disc Remaining Time
Indication
During recording, press DISPLAY repeatedly until the desired
indication appears on the front display panel.
● Each time you press DISPLAY, the time indication changes as
follows:
Elapsed recording time ] Disc remaining time ] Clock ] (Back to
the beginning)
Receiving Stereo And Bilingual Programmes
Your unit is equipped with a Sound-Multiplex decoder (A2) and a
Digital stereo sound decoder (NICAM) making reception of stereo
and bilingual broadcasts possible.
When the channel is changed, the type of broadcast being
received will be displayed on the TV screen for a few seconds.
NOTES:
● “SUPERIMPOSE” must be set to “AUTO”. Otherwise the on-screen
displays will not appear. (
● If the quality of stereo sound being received is poor, the broadcast
might be received in monaural with better quality.
Selection Of The Audio Channel To Be Recorded On A
Disc
When a programme is recorded on a DVD-RAM or DVD-RW disc in
VR mode, all audio channels of the receiving programme are
recorded on the disc. When you record a programme on a DVD-R
or DVD-RW disc in video mode, select the desired audio channel
(“NICAM” or “MONO”) to be recorded on the disc. (
NOTE:
Before playing back a programme recorded in stereo, or a bilingual
programme, refer to “Audio Channel Selection” on page 29.
Recording Features
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
● Press HDD so that the HDD lamp lights up on the unit.
7
HDD
TV AV/ VIDEO
HDD
DISPLAY
PR+/-
CABLE/SAT
DVD
TV
HDD Lamp
Type of Broadcast Being
Received
On-screen Display
A2 Stereo
A2 Bilingual
Regular Monaural
NICAM Stereo
NICAM Bilingual
NICAM Monaural
DR-MH30EU_00.book Page 39 Tuesday, June 29, 2004 5:41 PM