JVC RX-7012RSL - Manual (Page 35)

32
Tuner
You can always perform the following operations:
FM/AM : Alternates between FM and AM (MW/LW).
After pressing FM/AM, you can perform the following operations:
1 – 10, +10 : Selects a preset channel number directly.
For channel number 5, press 5.
For channel number 15, press +10, then 5.
For channel number 20, press +10, then 10.
TUNING +/– : Tunes into stations.
FM MODE : Changes the FM reception mode.
PTY SEARCH : Searches for a program by PTY codes.
PTY +/– : Selects the PTY codes.
DISPLAY : Shows the RDS signals.
Sound control section (Amplifier)
You can always perform the following operations:
SURROUND ON/OFF : Turns on or off the Surround modes –
Dolby Pro Logic, Dolby Digital, and
DTS Digital Surround.
DSP MODE : Selects the DSP modes.
After pressing SOUND, you can perform the following operations:
SUBWOOFER +/– : Adjusts the subwoofer output level.
CENTER +/– : Adjusts the center speaker output level.
REAR•L +/– : Adjusts the left rear speaker output level.
REAR•R +/– : Adjusts the right rear speaker output level.
EFFECT : Selects the effect level.
TEST : Turns on or off the test tone output.
Note:
After adjusting sounds, press the corresponding source selecting
button to operate your target source by using the 10 keys; otherwise,
the 10 keys cannot be used for operating your target source.
CD player
After pressing CD, you can perform the following operations on the
CD player:
PLAY 3:
Starts playing.
4 4 4 4 4: Returns to the beginning of the current (or
previous) track.
¢ ¢ ¢ ¢ ¢: Skips to the beginning of the next track.
STOP 7: Stops playing.
PAUSE 8:
Pauses playing. To release it, press PLAY
3.
1 – 10, +10 : Selects a track number directly.
For track number 5, press 5.
For track number 15, press +10, then 5.
For track number 20, press +10, then 10.
For track number 30, press +10, +10, then 10.
Operating JVC’s Audio/Video Components
You can operate JVC’s audio and video components with this receiver’s remote control, since control signals for JVC
components are preset in the remote control.
Operating Audio Components
IMPORTANT:
To operate JVC’s audio components using this remote control:
• You need to connect JVC audio components through the COMPU
LINK (SYNCHRO) jacks (see page 31) in addition to the
connections using cables with RCA pin plugs (see pages 5 and 6).
• Aim the remote control directly at the remote sensor on the
receiver.
• If you use the buttons on the front panel, the remote control will
not operate that source. To operate a source with the remote
control, the source must be selected using source selecting buttons
on the remote control.
• To operate the cassette deck or CD recorder using the COMPU
LINK remote control system, set the source name correctly. (See
page 13.)
• Refer also to the manuals supplied with your components.
* When you press one of the following buttons, the remote
control operation mode appears on the display window for
about 10 seconds.
Buttons on the Remote Control Remote Control Operation Mode
FM/AM TUNER
CD CD
PHONO PHONO
TAPE/CDR TAPE
DVD DVD
DVD MULTI DVD
TV/DBS TV
VCR VCR
CATV/DBS CONTROL DBS
CONTROL Current setting or VCR or TAPE
or CDDSC
SOUND SOUND
Ex.: When you
press CD button
CONTROL +
− +
− +
−
2 3 1
5 6 4
8 9 7/P
0 +10 10
BASS BOOST EFFECT
MENU
ENTER
TEST
SOUND
MUTING
CH TV VOL
PLAY
STOP
/REW FF/
VOLUME
CATV/DBS
CONTROL
TV/VIDEO
REC
TUNING
PAUSE
PAUSE
RETURN FM MODE 100+
CONTROL
A/V CONTROL RECEIVER
RM-SRX7010R
CATV/DBS VCR TV AUDIO
DSP
MODE INPUT ON/OFF
DVD MUILTI DVD CD
TAPE/CDR
TREBLE
TV/DBS VCR PHONO
FM/AM
BASS
SURROUND ANALOG/DIGITAL SLEEP
+
−
– SUB WOOFER +
– REAR • R +
– REAR • L +
– CENTER +
− − + +
PTY– PTY SEARCH
DISPLAY
PTY+
EN31_40.RX-7010&7012R[B]_f 01.1.9, 5:25 PM 32