Outputs, Ch1 ch2, Ch2 ch1 ch2 ch1 – JBL MPC User Manual
Page 7: 8 4 2 ω ω ω
6
Outputs
Covered barrier strips located on the rear panel allow safe, shockproof speaker cable connec-
tions to the amplifier outputs. See the diagrams for details on connecting speakers and/or
distributed (25V, 70V, 100, 140V, and 200V) lines. Insulated connectors of the type shown are
recommended. Always make sure the amplifier is turned off before you change any output
connections or before lifting the safety shroud.
For driving 140V or 200V distributed lines, the amplifier must be set into bridged mono
mode. See Bridged Mono Mode section later in this manual for information about this
mode.
Lift safety shroud.
Loosen screw terminals.
Insert wire connectors
under screws.
Tighten screw terminals.
Lower safety shroud.
BRIDGE
MONO
BRIDGE
MONO
CH1
CH2
OUTPUT
OUTPUT
16
8
4
Ω
Ω
Ω
BRIDGE
MONO
BRIDGE
MONO
CH1
CH2
OUTPUT
OUTPUT
8
4
2
Ω
Ω
Ω
8
4
2
Ω
Ω
Ω
CH2
CH1
CH2
CH1
BRIDGE
MONO
BRIDGE
MONO
LOW IMPEDANCE
LOW IMPEDANCE
DIR. OUTPUT
DIR. OUTPUT
ISOL.OUTPUT
ISOL.OUTPUT
AUDIO TRANSFORMER
AUDIO TRANSFORMER
70V
70V
25V
25V
100V
100V
0
70 100
0
70 100
16
8
4
Ω
Ω
Ω
CH1
CH1
BRIDGE
MONO
LOW IMPEDANCE
DIR. OUTPUT
ISOL.OUTPUT
AUDIO TRANSFORMER
70V 25V
8
4
2
Ω
Ω
Ω
100V
0
70 100
CH1
CH1
BRIDGE
MONO
LOW IMPEDANCE
DIR. OUTPUT
ISOL.OUTPUT
AUDIO TRANSFORMER
70V 25V
100V
0
70 100
CH1
CH1
BRIDGE
MONO
LOW IMPEDANCE
DIR. OUTPUT
ISOL.OUTPUT
AUDIO TRANSFORMER
70V 25V
100V
0
70 100
CH1
CH1
BRIDGE
MONO
LOW IMPEDANCE
DIR. OUTPUT
ISOL.OUTPUT
AUDIO TRANSFORMER
70V 25V
100V
0
70 100
CH2
CH1
CH2
CH1
BRIDGE
MONO
BRIDGE
MONO
LOW IMPEDANCE
LOW IMPEDANCE
DIR. OUTPUT
DIR. OUTPUT
ISOL.OUTPUT
ISOL.OUTPUT
AUDIO TRANSFORMER
AUDIO TRANSFORMER
70V
70V
25V
25V
100V
100V
0
70 100
0
70 100
TO 140V LINE
CH2
CH1
CH2
CH1
BRIDGE
MONO
BRIDGE
MONO
LOW IMPEDANCE
LOW IMPEDANCE
DIR. OUTPUT
DIR. OUTPUT
ISOL.OUTPUT
ISOL.OUTPUT
AUDIO TRANSFORMER
AUDIO TRANSFORMER
70V
70V
25V
25V
100V
100V
0
70 100
0
70 100
TO 200V LINE
Output connection for MPC, bridged mono mode.
Output connection for MPC, parallel or stereo mode.
Output connection for MPC “T” models, bridged
mono mode.
Output connection for MPC “T” models, direct low
impedance.
Output connection for “T” models,
25 volt line.
Output connection for “T” models,
50 volt line.
Output connection for “T” models,
100 volt line.
Output connections for “T” models, bridged
mono mode, 140 volt line
Output connections for “T” models, bridged
mono mode, 200 volt line