JVC DLA-HX2E - Manual (Page 39)

39
Adjustments and Settings Using Menus
e
“Options” menu (“Page 2”)
Adjustment item (press ᮡ / ᮢ ) Adjustment content (press ᮤ / ᮣ )
“Sleep time[min]” Sets the length of sleep time which, when
lapsed, automatically puts the projector
into stand-by state if no signal is input-
ted.
Setting value: “15”, “30”, “60”, “OFF”
{“OFF”}
“Menu color” When “ON”, menu becomes transparent
and the background can be seen through
it.
Setting value: “OFF”, “ON”
{“OFF”}
“PC2(BNC)” Sets whether to use the BNC connector
on the back of the projector as an “RGB”
signal input terminal or as a “YP
B P R ”
(color-difference) signal input terminal.
Please reset it based on the connected
apparatus.
•
The input will be “RGB” irrespective
of the PC signal setting.
Setting value: “RGB”, “YP b P r ” {“YP b P r ”}
“DIST” Image of high resolution can be achieved.
Set as required.
This is turned “ON” when the [OPERATE]
button is pressed.
Setting value: “OFF”, “ON”
{Varies with signals}
“SCART” Connects to a Europe-adapted SCART
plug and turns it “ON” during component
input.
Connect the Image Signal cable to the
[RGB] terminal of the [PC2] input termi-
nal and the Sync Signal cable to the
[VIDEO IN] terminal.
Setting value: “OFF”, “ON”
{“OFF”}
“RS-232C [bps]” Sets the communication speed (signal
transmission speed) when communicat-
ing with a computer by using the [RS-
232C] terminal. Please set the baud rate
for transmission.
Setting value: “9600”, “19200”
{19200}
“SXGA” Select “1400” to project SXGA+ signal.
Setting value: “1280”, “1400”
{1280}
“PC 3” Set whether to use PC input or HDCP
compatible video signal when using [PC3]
terminal as input. Set according to the
connecting equipment.
Setting value : “PC”, “HDCP”
{“HDCP”}
r
“Language” menu
Select the language in this language menu with the CURSOR buttons
(
ᮡ
/
ᮢ
).
Setting value : [ ] (Japanese), [English], [Deutsch] (German),
[Español] (Spanish), [Italiano] (Italian), [Français]
(French), [Por tuguês] (Por tuguese) and [
]
(Korean).
{[English]}
• Some words in the menu and proper nouns such as “VIDEO”, “NTSC”,
“QUICK ALIGN...” are shown only in English.
p
“Capture start”
The status of capture is displayed in bold.
“Capt. in prog. (approx. 2min)” The image is being read into the projec-
tor. During this time interval, the projec-
tor will not respond to any command sig-
nal inputted by the user.
“Signal can not be captured” Clear the message with the [EXIT] but-
ton and input appropriate signals.
“Reduce capt. size” Clear the message with the [EXIT] but-
ton and decrease the signal size.
•
Depending on the image content,
there will be cases where certain sig-
nals cannot be captured while others
of the same size can be.
q
“Options” menu (“Page 1”)
The items of the “Options” menu shown below can be adjusted.
• The “Options” menu consists of two pages (“Page 1” and “Page 2”).
“Page 1”
Adjustment item (press ᮡ / ᮢ ) Adjustment content (press ᮤ / ᮣ )
“Color profile” Sets the color table.
[
Press the [ENTER] button to enter the
“Color profile” menu w.
“Menu display” Sets whether the menu display automati-
cally clears after 15 seconds.
Values : “15sec”, “ON”
{“15sec”}
“Line display” Sets whether the line display is shown for
about 5 seconds.
Values : “5sec”, “OFF”
{“5sec”}
“Flip H” Reverses image left to right.
Values : “ON”, “OFF”
{“OFF”}
“Flip V” Inverses image upside down.
Values : “ON”, “OFF”
{“OFF”}
“Page 2” Displays “Page 2” of the “Options” menu.
[
Press the [ENTER] button to enter the
“Options” menu (“Page 2”) e.
w
“Color profile” menu
To choose the color table of the image signals, press the (
ᮡ
/
ᮢ
) CUR-
SOR buttons. When using “Color profile”, set the “Color temp.” to “D65”.
• No display in the absence of image signal input.
Values : “------”, “HDTV”, “MacRGB”, “NTSC”, “PAL”
{Varies with signals}