Philips FW930R - Manual (Page 25)

25
English
Note:
– For 'EASY SET' feature, please refer to
page 13.
Tuning to radio stations
1 Press TUNER (FM•AM) to select
TUNER mode.
™ “TUNER” will be displayed.
A few seconds later, the current radio
frequency will be displayed.
2 Press TUNER (FM•AM) again to select
the desired waveband : FM or AM.
3 Press TUNING à or á for more than
one second, then release.
™ The display will show “SEARCH”
until a radio station with sufficient
signal strength is found.
• Repeat this procedure until the desired
station is reached.
FRONT NEWS T.A.
REPEAT PROGRAM TIMER
PROG
BACK HSD
SHUFFLE REC
LW MW AM
SOUND NAVIGATION
DUB
(HSD)
REC
MINI HIFI SYSTEM
FM
STEREO
60Hz 500Hz 250Hz 1KHz 2KHz 4KHz 8KHz
VOLUME
INCREDIBLE
SURROUND DYNAMIC BASS
BOOST
TAPE CD
CLOCK/
TIMER
SIDE A•B
TUNER AUX
PRESET ▲ ▲
STOP•CLEAR SEARCH • TUNING PLAY PAUSE PREV NEXT
C D 1 • 2 • 3 CDR TAPE 1 • 2
DIGITAL
SOUND CONTROL
FM • AM
A. REV
STANDBY
ON
• To tune to a weak radio station, briefly
press TUNING à or á repeatedly
until the display shows the desired
frequency and/or when the best
reception has been obtained.
Storing Preset Stations
You can store up to 40 radio stations in the
memory. When a preset radio station is
selected, the preset number appears next
to the frequency on the display.
Automatic programming
1 Press TUNER (FM•AM).
2 Press PROGRAM for more than one
second.
™ The
PROGRAM flag starts flashing and
“ AUTO” will be displayed.
TUNER
™ The system will search for every
available station in the FM waveband
first, then search by the AM
waveband.
™ All available radio stations will be
stored automatically. The frequency
and preset number will be displayed
briefly.
™ The system will stop searching when
all the available radio stations are
stored or when the memory for 40
preset radio stations is used.
™ The system will remain tuned to the
last stored preset radio station.
Notes:
– You can cancel the automatic
programming by pressing PROGRAM or
STOP•CLEAR Ç (on the system only).
– If you want to reserve a section of
preset numbers, for example preset
numbers 1 to 9, select preset 10 before
starting automatic programming: only
the preset numbers 10 to 40 will be
programmed.
Manual programming
1 Press TUNER (FM•AM).
2 Press TUNER (FM•AM) again to select
the desired waveband : FM or AM.
3 Press PROGRAM for less than one
second.
™ The
PROGRAM flag starts flashing.
™ The next available preset number will
be displayed for selection.
4 Press TUNING à or á to tune to the
desired frequency.
• If you wish to store the radio station to
another preset number, press PRESET
4 or 3 to select the desired preset
number.
5 Press PROGRAM again.
™ The PROGRAM flag disappears and the
radio station will be stored.
• Repeat the steps 3 to 5 to store other
preset radio stations.
Notes:
– When 40 radio stations are stored and
you attempt to store another radio
station, the display will show "FULL”.
If you want to change an existing preset
number, repeat steps 3 – 5.
– You can cancel manual programming by
pressing STOP•CLEAR Ç (on the
system only).
– During programming, if no button is
pressed within 20 seconds, the system
will exit program mode automatically.
Tuning to Preset Radio
Stations
• Press PRESET 4 or 3 to select the
desired preset number.
™ The preset number, radio frequency,
and waveband appear on the display.