Meade Instruments RCX400 - Manual (Page 16)

16
Parts Listing
Getting the telescope ready for first observations requires only a few minutes. When
first opening the packing box, note carefully the following parts:
ܖ RCX400 Telescope with fork mount system and GPS Receiver
ܖ AutoStar II handbox and interface coil cord; handbox holder
ܖ 8 x 50mm viewfinder assembly
ܖ 2" diagonal mirror and 2” visual back barrel
ܖ Series 5000 UltraWide 24mm eyepiece
ܖ Variable height tripod
ܖ USB cable and software CD ROM
How to Assemble the Tripod
Remove the parts of the tripod from the shipping carton. Assembly of the tripod will
take just a few minutes.
To assemble the tripod:
1. Slide a leg (1) into a leg receptacle ( Fig. 7), making sure that the screw (3) in the
leg ( Fig. 8) slides into the groove (4) on the receptacle (Fig. 9).
2. Rotate the leg attachment lock (6) and tighten to a firm feel.
3. Press and hold down the trigger release lever (5) slide the tripod leg to the
desired length (thereby setting the height of the tripod). See
Fig. 11. Let go of the
trigger when the tripod leg is at the desired length.
5. Repeat steps 1 through 4 for the other two tripod legs. The tripod should now be
stable.
How to Assemble Your Telescope
The telescope’s fork mounting base attaches directly to the tripod. The telescope in
this way is mounted in an “altazimuth” (“altitude-azimuth,” or “vertical-horizontal”) for-
mat. It is recommended that two people attach the mount to the tripod.
Caution for 12” and 14” model users: Due to the weight and size of
these products, please use extreme caution whenever assembling,
disassembling, lifting, transporting or storing these products. Two or more
persons should always be used whenever performing any of these tasks.
Disregard for the above warning could result in serious injury or death.
Note: The field tripod also can be used in conjunction with the optional
equatorial wedge (see your wedge’s instruction sheet for more
information) for long exposure astrophotography.
The tripod base comes with a tangent arm attached for use with the superwedge.
To attach the mount:
1.
Take note of the T-handle under the tripod base. The T-handle is spring-mounted
into position. Note also that there is a hole on the bottom side of the mount base.
2. Lift the mount and position the mount base over the tripod base. Line up the hole
on the mount base over the T-handle rod. When they are lined up, place the
mount down onto the rod and the rod will “pop up” into the hole (
Fig. 12).
3. Rotate the T-handle until the rod is tightened to a firm feel ( Fig. 13).
To install the batteries:
Assembly of the
RCX 400 telescope requires eight C-cell (user-supplied) batteries or
the optional RCX AC Wall Adapter to a standard 115v home outlet . Plug the adapter
into the 12vDC In port of the computer control panel (
B, Fig. 1d).
1. Turn the Dec. lock ( 17, Fig. 1a) counterclockwise to unlock the the optical tube
( 19, Fig. 1a). Move the optical tube to the position depicted in Fig. 1a and turn
the Dec. lock clockwise to a firm feel to relock the position of the optical tube.
2. Remove the battery compartment covers ( 7, Fig. 1a) and carefully remove the
battery holders, being mindful of the connector wires ( Fig. 15). Insert four user-
supplied C-cell batteries into each battery holder, oriented as shown on the dia-
gram on the battery slots inside the battery holder. Return the battery holders to
their respective compartments and replace the covers.
Caution: Use care to install batteries as indicated by the battery
GETTING STARTED
Fig. 11: Lift the trigger lever (5) so
that you can adjust the height of the
tripod leg.
Fig. 7: Attach leg (1) to leg
receptacle (2).
Fig. 8: Slide the screw (3)...
Fig. 9: ... into groove on the
receptacle (4).
Fig. 10: Tighten the leg adjustment
lock (6).
f
B
c
d
e
g
f