MGE UPS Systems EX-7 - Manual (Page 8)

Figures
figure description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page
1-1: Tower Configuration with Power Module, Battery Module,
and optional Transformer Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 4
1-2: Rack Configuration with Power Module, Battery Module,
and optional Transformer Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 5
1-3: Rear panel of the Power Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 6
1-4: Rear Panel of the Battery Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 6
1-5: Rear Panel of the optional Transformer Module. (PN 86211) . . . . . . . . .1 — 7
1-6: View of typical control panel interface. . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 7
1-7: Power Module Rail Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 8
1-8: Battery/Transformer/CLA Module Rail Kit. . . . . . . . . . . . . . . . . . . . . . . . .1 — 8
1-9: Typical back-up time with multiple EXB’s at full load. . . . . . . . . . . . . . . .1 — 9
1-10: Typical Battery Integration kit with casters setup. . . . . . . . . . . . . . . . . .1 — 10
1-11: Typical Transformer Module contents and connections. . . . . . . . . . . . .1 — 11
1-12: CLA Module Contents and Connections. . . . . . . . . . . . . . . . . . . . . . . . .1 — 12
2-1:
Contents of EX 5/7/11RT Power Module. . . . . . . . . . . . . . . . . . . . . . . . .2 — 2
2-2: Contents of EXB 5/7/11RT Battery Module. . . . . . . . . . . . . . . . . . . . . . . .2 — 3
2-3: Tower Configuration of Standard System and
Optional Transformer Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 5
2-4: Typical orientation of the logo and control panel.
(Power Module shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 6
2-5: Accessing Battery Pack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 6
2-6: Rack mounting of the Power Module onto the rails. . . . . . . . . . . . . . . . .2 — 7
2-7: Input/Output Box Bracket System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 8
2-8: RS232 Communication Cable Connection. . . . . . . . . . . . . . . . . . . . . . . .2 — 9
2-9: Relay Pin Connections for Communication Port. . . . . . . . . . . . . . . . . . .2 — 10
2-10: Communication Card Slot with Network
Management Card installed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 10
2-10a: Activation of Remote Emergency Power Off function
using a contact normally open switch. . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 12
2-10b: Activation of Remote Emergency Power Off using a
contact normally closed switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 12
2-11: Power Module I/O Box Terminal Block Diagram. . . . . . . . . . . . . . . . . . .2 — 13
2-12: Normal AC Input and Output Cables installation. . . . . . . . . . . . . . . . . . .2 — 14
2-13: View of EX RT Transformer Module connected downstream
for 120/208/240 Vac outputs (shown with one EXB). . . . . . . . . . . . . . . .2 — 15
2-14: Normal AC Input, Bypass AC, and Output Cables Installation,
and Simplified Connection Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 16
2-15: Accessing Terminal Blocks for Input and Output power cables. . . . . . .2 — 17
2-16: Rear view of Battery Module cable connections. . . . . . . . . . . . . . . . . . .2 — 18
2-17: Rear view of CLA Module cable battery and AC input connections . . . .2 — 19
EX 5/7/11RT Systems
Contents c iv 86-86000-00 B00