Marantz ZR6001 - Manual (Page 11)

ENGLISH
8
m Cursor ( , , , ) / ENTER buttons
(when AMP mode is selected)
Use these button when operating the SETUP MAIN
MENU.
, MENU OFF button
(when AMP mode is selected)
This button is used to exit from the SETUP MAIN
MENU.
. Numeric buttons 1 to 9 / Surround mode
buttons
Numeric buttons
These buttons are used to enter figures in the selec-
tion of a tuner preset station and station name pre-
set or to set select a CD track number, etc. The func-
tions of these buttons are dependent on the function
button selected.
Surround mode buttons
(when AMP mode is selected)
These buttons are used to select the surround mode.
⁄0 P.SCAN (Preset scan) / V(Video)-OFF
button
(when TUNER mode is selected)
This button is used to start preset scan when
ZR6001 is selected TUNER mode.
(when AMP mode is selected)
This is used when switching the video signals from
the various monitor outputs to Video-Off mode.
(See page 31)
⁄1 0 / A/D button
0 button
This button is used to enter the number “0”
A/D button (when AMP mode is selected)
This is used to switch between the analog and
digital inputs.
⁄2 CONTROL buttons
These buttons are used when operating the CD
player, TAPE deck, etc.
The function of these buttons are dependent on the
function button selected.
For the controllable functions of each input function,
please refer to controllable function table on the page
11.
⁄3 SUB-T (Title) / ATT (attenuator) button
When the input signal is too high and the voice dis-
torts even while adjusting the ZR6001 VOLUME
control, turn on this function. “
ATT ” is illuminated
when this function is activated.
The input level is reduced. Attenuator is invalid for
the output signal of “REC OUT”. (See page 31)
Note:
• This function is unavailable while the digital input
is selected.
⁄4 INPUT/DISC+ / CH.SEL buttons
This button is used to enter the input level setup
menu.
⁄5 TREBLE UP ( ) /DOWN ( ) buttons
These buttons are used to adjust the tone control of
high frequency sound for left and right speaker.
⁄6 BASS UP ( ) /DOWN ( ) buttons
These buttons are used to adjust the tone control of
low frequency sound for left, right and subwoofer
speaker.
⁄7 MEMO button
Memory enable button for various preset functions.
⁄8 CLEAR button
This button is used to cancel for certain memory or
programming operations.
⁄9 DISPLAY button
Selects the display mode for the front display of the
ZR6001.
¤0 NIGHT button
Pressing this button prevents the Dolby Digital sig-
nal from playback at a loud voice. This function re-
duces the voice by 1/3 to 1/4 at maximum. Thus, it
eliminates the occurrence of an abruptly loud voice
at night. However, the function is valid only in the
case when the Dolby Digital signal is entered into
OPTICAL or COAXIAL and data to compress the
voice exists in the signal to be played back.
When this button is pressed, the “
NIGHT ” indicator
is illuminated.
REMOTE CONTROL
OPERATION
FUNCTION AND OPERATION
The provided remote control unit is a universal
remote controller. The
POWER button, numeric
buttons and control buttons are used in common
across different input source components.
The input source controlled with the remote control
unit changes when one of the input selector
buttons is pressed.
z Transmitting indicator
Lights up during a button is pressed and an infrared
signal is sending.
x (Main) POWER buttons
(when AMP mode is selected)
Press to switch the power of the ZR6001 ON or OFF
after pressing the
AMP button.
c Input selector buttons/ FUNCTION
SELECTOR buttons (AUDIO/VIDEO INPUT)
These buttons are used to select a Audio or Video
source component. Press one of these buttons once
to change the function of the remote control. Press
same button within 2 seconds, the input function of
the ZR6001 is changed.
Audio function sources such as CD, TAPE, CDR/
MD, and TUNER may be selected in conjunction
with a Video source.
This feature (Sound Injection) combines a sound
from one source with a picture from another.
Choose the video source first, and then choose a
different audio source to activate this function.
Notes:
• CDR/MD button is set CDR function at initial.
To switch MD function, press and hold down
CDR/MD button and press 2 button.
• To return CDR function, press and hold down
CDR/MD button and press 1 button.
v MAIN VOLUME UP ( ) /DOWN ( ) buttons
Main volume control of the ZR6001. The front, sur-
round, center and subwoofer channel volumes con-
trolled by these buttons simultaneously.
b MUTE button
Muting button of the ZR6001. Press this button de-
crease the sound temporarily. Press this button
again to return to the previous sound.
When this button is pressed, “
MUTE ” indicator lights
up.
n MENU button
(when AMP mode is selected)
This button is used to enter the SETUP MAIN MENU.
ENTER
CH.SEL LIP.SYNC
PTY SUB-T/ATT AUDIO INPUT/DISC+
F.DIRECT RDS
TUNE/SEARCH
T-MODE
TREBLE
CHANNEL/SKIP
BASS
A/D P.SCAN/V-OFF
7.1CH IN STEREO MCH-ST
MEMO CLEAR
DISPLAY
NIGHT CSII EX/ES VIRTUAL
DTS PURE DIRECT AUTO
3 2 1
6 5 4
9 8
0
7
T.TONE MENU OFF SET UP/
MENU OSD
VOL. TV VOL. MAIN SLEEP MUTE
AMP AUX1
TUNER CD TAPE CDR/MD
DVD
POWER
VCR1 DSS/VCR2 TV
SYSTEM REMOTE CONTROLLER
RC5500SR
,
m
n
b
v
c
x
z
⁄1
⁄2 ⁄5
¤3
¤2
¤1
¤0
⁄9
⁄8
⁄7
⁄6
¤4
⁄4
⁄3
¤5
.
⁄0
06.3.6, 4:26 PM Page 8