Cdm-3200 – Gemini CDM-3200 User Manual

Page 5

PITCH BEND mode the JOG WHEEL will function the same

as the PITCH BEND allowing you to speed up (FORWARD)

or slow down (REWIND) the music clockwise being (FOR-

WARD) and counter clockwise being (REWIND).

JOG MODE BUTTON: When the JOG MODE BUTTON is il-

luminated it indicates the JOG WHEEL is in SEARCH MODE,

and when not illuminated it indicates that the JOG WHEEL is

in PITCH BEND MODE.

DISPLAY: The DISPLAY shows the track number, pitch val-

ue, pitch bend, single, continue (for continuous play), play/

pause modes, fast forward/reverse modes, loop mode, re-

loop mode, PGM, repeat modes, the playback display bar,

and three different time displays. These times displays are

TIME ELAPSED on the track, TIME REMAINING on the disc

and TIME REMAINING on the track. Time is measured in

minutes, seconds and frames.

PGM: Allows you to create a set playlist. To program a set

list into the CDM-3200 memory, begin by stopping the unit

from play and pressing PGM to begin the set list. Select a

track by using the track selection button to scan to the first

track to be placed in the set list. When you have selected the

proper track press PGM and the CDM-3200 will be ready to

set your next selection. Repeat the previous steps until you

have completed your play list, then press play to begin the

set list.

SINGLE: Pressing the SINGLE button engages SINGLE

mode, in this mode the CDM-3200 will play one song and

then stop. Pressing the SINGLE button again will then acti-

vate CONTINUOUS mode causing the unit to play continu-

ously (after the last track, the unit will return to the first track

of the disc and continue to play).

TIME: The TIME button switches the time display between

three available sources, these three are TIME ELAPSED on

the track, TOTAL REMAIN on the disc and REMAIN on the

track. TIME ELAPSED indicates how much time has cur-

rently gone by since the play button was pressed, TOTAL

REMAIN will count down the time remaining on the entire

disc and REMAIN counts down the time that is left before the

end of the track.

PITCH: Hold the PITCH button to activate the PITCH CON-

TROL SLIDE. Pitch ranges can be controlled through the

use of the PITCH CONTROL SLIDER. Hold the PITCH but-

ton again to deactivate this mode.

PITCH CONTROL SLIDE: Moving the PITCH CONTROL

SLIDE up or down will change the pitch percentage +/ -

12%.

PITCH BEND: Pushing the PITCH BEND BUTTONS will au-

tomatically raise the pitch up to +16% or lower the pitch down

to -16% from the existing pitch setting. Releasing the buttons

will return the pitch to the original pitch setting. You can use

this function to match the beat when mixing from one song to

another.

LOOP SECTION: A LOOP repeats the section between the en-

try point (IN) and the exit point (OUT).

A. To set a loop while the unit is playing, start by pressing

the IN BUTTON (it will light up)

B. When you reach the desired end loop point press the

OUT BUTTON (it will also light up). The loop will continue

playing until you press the OUT BUTTON again allowing

the music to continue from that point on.

C. To re-engage the loop you must press the RELOOP

BUTTON.

D. When you have released your loop the OUT BUTTON

will turn OFF and the IN BUTTON will remain lit to indicate

that your loop is stored in the CDM-3200 memory.

E. Pressing the IN BUTTON again while the unit is playing

will erase the previously saved loop while saving your new

loop entry point.

F. Press OUT to exit the loop and save a new complete

loop.

G. Press RELOOP to return to the beginning of the previ-

ously saved loop from normal play. Press RELOOP repeat-

edly to cause the loop to stutter.

NOTE: THE FIRST LOOP WILL HAVE A PAUSE AT THE EXIT

POINT, WHILE ALL OTHERS WILL BE SEAMLESS.

PLAY / PAUSE: Each press of the PLAY / PAUSE BUTTON

causes the operation to change from PLAY to PAUSE or from

PAUSE back to PLAY. The PLAY/PAUSE BUTTON remains lit

when in PLAY mode, while it blinks in PAUSE mode.

CUE: While the unit is playing and after the cue point has been

programmed, pressing CUE will cause the CD player to en-

ter the PAUSE mode (PLAY/PAUSE BUTTON blinks) at the

programmed cue point (the CUE LED is lit). Holding down the

CUE button changes the function to preview, and allows you to

stutter start or play from the programmed CUE POINT. Releas-

ing the CUE button will return the CD to the preset CUE point.

TRACK SELECTION: The TRACK SELECTION buttons let

you select the track to play. +10 allows you to scan through the

track selection in increments of 10. TRACK SKIP allows you to

scan through each track one at a time. Select the track desired

by pressing the TRACK SELECTION BUTTON.

NOTE: ONCE YOU HAVE SKIPPED TO ANOTHER TRACK,

YOU MAY NOT GO BACK TO YOUR PROGRAMMED CUE

POINT. YOU MUST BEGIN YOUR CUE SELECTION OVER

AGAIN, THE CUE WILL BE PRESET TO THE BEGIN-NING

OF THE NEWLY SELECTED TRACK.

CDM-3200