FUNAI CR270TT8 - Manual (Page 10)

10
EN
I
NITIAL SETTING
Initial Setup
This section will guide you through the unit’s initial setting which includes
selecting a language for your on-screen menu and “AUTO PRESET CH”, which
automatically scans and memorizes viewable channels.
Before you begin:
Make sure if the unit is connected to antenna or cable.
1
After making all the necessary connections, press
[POWER] to turn on the unit.
POWER
• This operation may take a few moments.
2
Use [CH K/L] or [VOL X] to select the on-screen
language from the choices on the left side of the TV
screen. (ENGLISH / ESPAÑOL / FRANÇAIS)
or
or
CH
CH
VOL
SELECT LANGUAGE
ENGLISH
NEXT:PRESS
CHK
ESPAÑOL
DESPUÉS:PRESIONE
CHL
FRANÇAIS
APRÈS:PRESSEZ
VOLX
• Press [CH K] for English.
• Press [CH L] for Spanish.
• Press [VOL X] for French.
3
Use [CH K/L] to select “D.S.T.” (Daylight Saving Time),
then use [VOL X/ Y] to set to “ON”.
or
CH
CH
or VOL VOL
1. PLEASE CONNECT ANTENNA TO
THE UNIT.
2. SET UP THE ITEMS WITH
, AND BUTTONS.
D.S.T. (Daylight Saving) [ON]
TIME ZONE [- - -]
AUTO PRESET CH (TV/DTV)
AUTO PRESET CH (CATV)
• You must set “D.S.T.” and “TIME ZONE” before
presetting channels.
4
Use [CH K/L] to select “TIME ZONE”, then use
[VOL X/ Y] to change the setting.
or
CH
CH
or VOL VOL
1. PLEASE CONNECT ANTENNA TO
THE UNIT.
2. SET UP THE ITEMS WITH
, AND BUTTONS.
D.S.T. (Daylight Saving) [ON]
TIME ZONE [- - -]
AUTO PRESET CH (TV/DTV)
AUTO PRESET CH (CATV)
[ALASKA] [HAWAII]
[ATLANTIC] [PACIFIC]
[EASTERN] [MOUNTAIN]
[CENTRAL]
5
5 Use [CH K/L] to select “AUTO PRESET CH(TV/DTV)”
for TV channels or “AUTO PRESET CH(CATV)“ for CATV
channels, then press [VOL X].
or
CH
CH
VOL
1. PLEASE CONNECT ANTENNA TO
THE UNIT.
2. SET UP THE ITEMS WITH
, AND BUTTONS.
D.S.T. (Daylight Saving) [ON]
TIME ZONE [ALASKA]
AUTO PRESET CH (TV/DTV)
AUTO PRESET CH (CATV)
• When the scanning and memorizing are completed,
the lowest memorized channel in the broadcasting
will be displayed.
Note:
• If you connect the cable system directly, contact the CATV
installer.
• If you press [POWER] or [MENU] during “AUTO PRESET CH”,
this setting will be canceled.
• The initial auto channel scan function can be executed for
either TV/DTV or CATV only once. If you want to scan both
TV/DTV and CATV, you need to select “CHANNEL SET” in
the main menu to scan and memorize other channels after
initial presetting is completed. (Refer to page 11.)
• You can cancel or exit the initial “AUTO PRESET CH” menu by
pressing [MENU].
• When no channel can be received by “AUTO PRESET CH”,
“NO TV SIGNALS” is displayed on the TV screen.
• If there is no signal input from the antenna terminal and
no operation for more than 5 seconds, “HELPFUL HINTS”
appears. Follow the instructions listed on the TV screen.
- HELPFUL HINTS -
1. PLEASE CHECK TO SEE IF THE
ANTENNA / CABLE / SATELLITE IS
PROPERLY CONNECTED.
2. DID YOU PERFORM
“AUTO PRESET CH”?
3. PLEASE REFER TO FRONT PAGE
OF THE OWNER’S MANUAL OR
REAR PANEL FOR SUPPORT LINE
INFORMATION.
Main Menu
This section describes the overview of the main menu displayed when you
press [MENU].
For more details, see the reference page for each item.
The main menu consists of the function setting items below.
Press [MENU] to display the main menu.
e.g.) digital TV mode
MENU
PICTURE
CHANNEL SET
[ENG]/ESP/FRA
V-CHIP SET UP
CAPTION [OFF]
DTV SET UP
• PICTURE
You can adjust the picture quality.
(Refer to “Picture Adjustment” on page 17.)
• CHANNEL SET
You can automatically scan the viewable channels and
remove those that are undesired.
(Refer to “Auto Channel Scan” on page 11.)
5
These operations are accessible by remote control. Some may also be accessible by controls on the main unit.
L4758UJ_EN.indd 10 L4758UJ_EN.indd 10 2006/12/11 22:06:54 2006/12/11 22:06:54