FUJITSU MHZ2250BJ - Manual (Page 311)

Index
C141-E280 IN-5
power amplifier ....................................... 4-13
power command ...................................... 6-10
power management
interface ...................................... 1-17, 1-18
power requirement .................................... 1-8
power save................................................. 6-8
power save controlled by interface
power management (IPM) ................... 6-11
power save mode................................ 1-2, 6-8
power save mode of interface ................. 6-11
power supply configuration....................... 4-4
power supply pin ..................................... 3-10
power supply segment............................. 3-10
power-on cashing function...................... 6-21
power-on reset....................................... 5-187
power-on sequence..................4-6, 4-7, 5-187
power-on, response to ............................... 6-2
primitive mnemonic .................................. 5-5
programmable filter circuit ..................... 4-11
protocol, command................................ 5-175
R
raw attribute value................................... 5-61
READ BUFFER.................................... 5-100
read circuit............................................... 4-11
READ DMA ........................................... 5-96
READ DMA EXT................................. 5-145
READ FP DMA QUEUED................... 5-169
READ FP DMA QUEUED
command protocol ............................. 5-185
READ LOG DMA EXT........................ 5-167
READ LOG EXT.................................. 5-148
READ LOG EXT log page 10h, data
format of ............................................ 5-150
READ LOG EXT log page 11h, data
format of ............................................ 5-151
READ MULTIPLE ................................. 5-89
READ MULTIPLE command,
execution example of........................... 5-90
READ MULTIPLE EXT ...................... 5-147
READ NATIVE MAX
ADDRESS......................................... 5-137
READ NATIVE MAX
ADDRESS EXT ................................ 5-146
READ SECTOR(S)................................. 5-32
READ SECTOR(S) EXT...................... 5-144
read segment buffer, using ...................... 6-16
READ VERIFY SECTOR(S) ................. 5-38
READ VERIFY SECTOR(S)
EXT ................................................... 5-164
read/write circuit .......................2-3, 4-3, 4-10
read/write circuit block diagram ............. 4-10
read/write preamplifier
(PreAMP) ............................................ 4-10
read-ahead cache ..................................... 6-13
read-ahead cache system ........................... 1-3
RECALIBRATE...................................... 5-31
recommended equipment........................... 3-8
recommended power-off sequence.......... 1-15
register - device to host............................ 5-16
register - host to device............................ 5-15
reliability ................................................. 1-13
reset ........................................................... 6-2
reset response........................................... 6-21
reset, power-on and COMRESET ......... 5-187
response to COMRESET........................... 6-4
response to power-on................................. 6-2
response to software reset.......................... 6-7
rewriting microcode data
(640 K bytes ), example of................... 5-45
ripple.......................................................... 1-8
rule for maintenance .................................. 7-2
S
SATA interface.......................................... 2-3
SATA interface cable
connection............................................ 3-11
SCT COMMAND SET ................5-76, 5-162
SCT READ DATA.......................5-82, 5-153
SCT STATUS REQUEST............5-72, 5-152
SCT WRITE DATA .....................5-83, 5-163
sector count field ..................................... 5-23
sector number field .................................. 5-23
SECURITY DISABLE
PASSWORD...................................... 5-135
SECURITY ERASE PREPARE ........... 5-130
SECURITY ERASE UNIT ................... 5-131
SECURITY FREEZE LOCK ................ 5-133
security password, content of ................ 5-128
SECURITY SET PASSWORD............. 5-126
SECURITY SET PASSWORD data,
contents of.......................................... 5-126
SECURITY UNLOCK .......................... 5-128
SEEK ....................................................... 5-40
seek operation.......................................... 4-17
selective self-test feature flag .................. 5-70
selective self-test log data
structure ............................................... 5-69
selective self-test pending
time [min] ............................................ 5-70
self-calibration........................................... 4-8
self-calibration content .............................. 4-8
self-diagnosis............................................. 1-3
self-diagnostics .......................................... 7-8
self-test execution status.................5-62, 5-68
self-test index .......................................... 5-68
self-test number ....................................... 5-68