InSinkErator F-C1100 Cold Only Faucet - Manual (Page 5)

b
b
a
a
Property Damage: Do not pinch or break copper
tubing. Do not distort the last 1" of tubing.
2
An assistant may be needed to hold
the faucet in place
while securing the base.
Follow these steps for installing chilled water tank with a cold only faucet.
Feed tube down through sink hole
until the base is at rest.
From under the sink, place the
semi-circular mounting plate onto
the threaded stud.
Place hex nut onto the threaded stud.
Ensure faucet is at desired angle.
Insert screwdriver into hole on side of
hex tool (creating a “T”), and use tool
to tighten nut and secure faucet.
Unpack faucet components.
On a firm, flat surface, carefully
straighten the copper tubing.
Ensure that the black O-ring is
properly seated in the base of the
faucet (the groove on the underside
of the faucet base).
Property Damage: Do not pinch or break tubing.
Do not distort the last 1" of tubing.
Pull on connection to ensure fully engaged.
Attach supplied quick connect elbow
to end of supplied blue 1/4" tube.
Attach quick connect elbow with
blue tube to water Outlet on front of
chilled water tank.
Measure distance from chilled water
tank outlet to water supply line on
faucet. Carefully trim blue tube to
correct length.
Using quick connect elbow, connect
blue tube to faucet water supply.
Property Damage: All tubes must be cut
squarely with no burrs.
3
Attach supplied quick connect elbow
to end of supplied white 1/4" tube.
Attach quick connect elbow to water
Inlet on front of chilled water tank.
Measure distance from water inlet
on chilled water tank to water
supply valve. Carefully trim white
1/4" tube, allowing ample slack
in tubing.
White Tape
Follow these steps for installing chilled water tank with a cold only faucet.
Property Damage: Join remaining tube to
cold water supply only. Water supply valves
must not prevent backwards flow.
Brass Nut
Ferrule
Brass Insert
Brass Nut
Ferrule
Plastic
tube
1 4
Inlet
Outlet
White Tape
Brass Nut
Ferrule
Brass Insert
Brass Nut
Ferrule
Plastic
tube
1 4
Inlet
Outlet
White Tape
For filtration installation instructions,
see installation guide packed with the
system.
Install a T-fitting (not included)
onto the cold water supply line.
Install dedicated water control
valve with 3/8" compression fitting
(not included).
Install brass nut, ferrule and tube
insert at the end of the white3/8"
tube from filter.
Insert the white 3/8" tube into the
3/8" compression fitting and tighten.
With optional InSinkErator filtration system:
Property Damage: Before plugging in
chilled water tank, check for leaks in all
water supply connections.
Turn on the cold water supply.
Depress the faucet handle and hold it
until water flows from the spout.
Allow water to run for at least 60
seconds after water begins to flow
from faucet.
5
Brass Nut
Ferrule
Brass Insert
Brass Nut
Ferrule
Plastic
tube
1
4
Inlet
Outlet
White Tape
9 8
Brass Nut
Ferrule
Brass Insert
Brass Nut
Ferrule
Plastic
tube
1 4
Inlet
Outlet
White Tape
Brass Nut
Ferrule
Brass Insert
Brass Nut
Ferrule
Plastic
tube
1 4
Inlet
Outlet
White Tape
b
Check all connections to ensure they
are tight and that there are no leaks.
Plug in chilled water tank.
Prior to drinking water from the
chilled water tank, run the water for
at least 5 minutes to flush lines.
Allow up to 60 minutes for
water to reach target temperature.
Electric Shock Hazard: A standard grounded
outlet is required under the sink. Do not use an
extension cord set with the chilled water tank.
Brass Nut
Ferrule
Brass Insert
Wing Nut
Plug
Fiber
Washer
Brass Nut
Ferrule
Wing Nut
Fiber
Washer
1 2
3
Plastic
tube
Property Damage: Join remaining tube to
cold water supply only. Water supply valves
must not prevent backward flow.
4
Install a T-fitting (not included)
onto the cold water supply line.
Install dedicated water control valve with
1/4" compression fitting (not included).
Place 1/4" brass insert (included)
into end of white tube.
Attach remaining end of the supplied
white 1/4" tube into the 1/4"
compression fitting and tighten.
With no filtration system: Brass Nut
Ferrule
Brass Insert
Brass Nut
Ferrule
Plastic
tube
1 4
Inlet
Outlet
White Tape
Brass Nut
Ferrule
Brass Insert
Brass Nut
Ferrule
Plastic
tube
1 4
Inlet
Outlet
White Tape
a a
a
INSTALLING THE COLD ONLY FAUCET
INSTALLING THE WATER TANK
FILL TANK & CONNECT POWER
WATER CONNECTION