Gardner Bender Mini-Eegor Hydraulic Bender User Manual
Page 6
WARRANTY: GB ELECTRICAL, INC. warrants its
products against defects in workmanship and
materials for 1 year from date of delivery to user.
Chain is not warranted. Warranty does not cover
ordinary wear and tear, abuse, misuse, overloading,
altered products or use of improper fluid.
WARRANTY RETURN PROCEDURE: When
question of warranty claim arises, send the unit to the
nearest GB Authorized Service Center for inspection,
transportation prepaid. Furnish evidence of purchase
date. If the claim comes under the terms of our
warranty the Authorized Service Center will REPAIR
OR REPLACE PARTS AFFECTED and return the unit
prepaid.
PARTS AND SERVICE: For quality workmanship and
genuine GB ELECTRICAL parts, select an Authorized
GB Service Center for your repair needs. Only
repairs performed by an Authorized Service Center
displaying the official GB Authorized sign are backed
with full factory warranty. Contact GB Electrical
(414) 352-4160 for the name of the nearest GB
Authorized Service Center.
REPAIR AND SERVICE INSTRUCTIONS: For repair service and parts contact your nearest GB ELECTRICAL
Service Center. The Service Center will provide complete and prompt service on all GB ELECTRICAL products.
GB Electrical, Inc.
An Applied Power Company
6101 N. Baker Road, Milwaukee, WI 53209
Phone: (414) 352-4160
FAX (414) 352-2377
RPS-0034 Rev. A
03/07
6
6
To Make a Stub-up or Kick Bend
1. Determine “H” dimension by measuring rise or
height needed. From “Diagonal Distance
Chart” on page 5, determine straight length of
pipe (D) needed to reach to desired turn-up
height (H) at desired bend angle.
2. Lay off this distance (D) from end of conduit
and make first mark.
3. From “Set-back Chart”, select proper set-back
dimension (S) corresponding to conduit size
and bend angle desired.
4. Measure distance (S) back from the first mark and make second mark (see figure above).
5. Place conduit in bender with second mark aligned with leading edge of U-strap (see figure above) and bend
conduit to desired angle.
D
D
S
1st Mark
2nd Mark (Position leading edge of U-Strap at this mark.)
Turn-up
or
Rise (H)
Angle
To Make an Offset Bend:
1. Make first mark at location determined either by edge of obstacle or by following “Kick Bend Instructions for
Mini-Eegor™ Benders” (page 5).
2. From the “Offset Chart” for the size of conduit to be bent, obtain measurement (B) for offset height (H) and bend
angle desired.
3. Make second mark at distance (B) beyond first mark and on opposite side of conduit as
illustrated below.
4. Place conduit in Mini-Eegor™ bender with first mark aligned with leading edge of U-strap (see figure below) and
make first bend to the desired angle.
5. Advance the bent conduit through the frame assembly of
the Mini-Eegor™ bender and rotate the conduit 180°, so
the second mark aligns with the leading edge of
the U-strap.
6. Complete offset by making second bend to the exact
same angle as the first bend.
Offset
or
Rise (H)
Angle
B
B
2nd Mark
1st Mark (on other side of conduit)
Measurement (B) (Inches)
Desired
Offset
Offset
Angle
➤ 15°
30°
45°
60°
(H)
Conduit
(Inches) Size
➤ 1”, 1
1
⁄
4
”, 1
1
⁄
2
”, & 2"
1”
1
1
⁄
4
”
1
1
⁄
2
”
2”
2
7
11
⁄
16
–
–
–
–
–
–
4
15
3
⁄
8
7
13
⁄
16
–
–
–
–
–
6
23
1
⁄
8
11
13
⁄
16
8
5
⁄
16
–
–
–
–
8
30
13
⁄
16
15
13
⁄
16
11
1
⁄
8
8
7
⁄
16
–
–
–
10
38
9
⁄
16
19
13
⁄
16
13
15
⁄
16
10
3
⁄
4
10
9
⁄
16
10
7
⁄
16
–
12
46
5
⁄
16
23
13
⁄
16
16
3
⁄
4
13
1
⁄
16
12
7
⁄
8
12
3
⁄
4
12
9
⁄
16
14
54
27
13
⁄
16
19
9
⁄
16
15
3
⁄
8
15
3
⁄
16
15
1
⁄
16
14
7
⁄
8
16
61
3
⁄
4
31
13
⁄
16
22
7
⁄
16
17
11
⁄
16
17
1
⁄
2
17
3
⁄
8
17
3
⁄
16
18
69
1
⁄
2
35
13
⁄
16
25
1
⁄
4
20
19
13
⁄
16
19
11
⁄
16
19
1
⁄
2
20
77
3
⁄
16
39
13
⁄
16
28
1
⁄
16
22
5
⁄
16
22
1
⁄
16
22
21
13
⁄
16
22
84
15
⁄
16
43
13
⁄
16
30
7
⁄
8
24
5
⁄
8
24
3
⁄
8
24
1
⁄
4
24
1
⁄
8
24
92
11
⁄
16
47
13
⁄
16
33
3
⁄
4
26
15
⁄
16
26
11
⁄
16
26
9
⁄
16
26
7
⁄
16
26
100
3
⁄
8
51
13
⁄
16
36
9
⁄
16
29
1
⁄
4
29
28
7
⁄
8
28
3
⁄
4
28
108
1
⁄
8
55
13
⁄
16
39
3
⁄
8
31
9
⁄
16
31
5
⁄
16
31
3
⁄
16
31
1
⁄
16
30
115
13
⁄
16
59
13
⁄
16
42
3
⁄
16
33
7
⁄
8
33
5
⁄
8
33
1
⁄
2
33
3
⁄
8