Fill-Rite TS SS F & W Precision Meter - Manual (Page 8)

Direction of Flow
TS Series flow meters can operate in either direction.
Standard assembly, when facing the flow meter, has the
flow going Left-to-Right, unless specified differently at time
of the order. A label with the word INLET is placed on the
inlet flange, as assembled at the factory. To change the
direction of flow:
1. Reverse the position of any accessories attached to the
flow meter.
2. If Quadrature pulse signal is used, reverse output leads
for channels A & B on the TBB (or SCL):
TBB SCL
L-to-R R-to-L
WHITE: On A On B
GREEN: On B On A
NOTE: The ELNC register is not W&M certified in
the EU.
The SCL is not yet approved for use in
the EU.
1 . 8
Flow Meter Communications & Direction of Flow
TS Series meters in F●● & W●● assembly have an internal
pulser. The pulse signal generated by the flow meter, can
be fed directly to most electronic registers. In such assem-
blies, flow meter calibration (or re-calibration) is through
correction of the K Factor (number of pulses/unit volume) in
the electronic register.
In some cases an SCL board (#13) is added to the flow me-
ter assembly. This signal conditioner is added when:
1.
Flow meter pulse frequency exceeds the electronic
register capacity at maximum flow rate. This can occur
at surprisingly low flow rates (see below).
2.
The electronic register requires a scaled pulse value
(1, 10, 100 or 1000 pulses/volume unit).
3.
Local authorities demand a mechanical calibration de-
vice. The SCL includes two dials with setting from 00
to 99. Changing the setting by 1, represents approx.
0.03% correction to the pulse signal.
NOTE: K Factors shown here are nominal (average).
Individual flow meters can vary slightly; and all flow
meters will shift to some degree with viscosity fluctu-
ations (see page 1.14)
Register m odel: LCR-II™
Frequency lim it: 625 Hz
FLOW
METER
MODEL GPM LPM
P P G ppl
TS10C 40 150 2176 575  1451 Hz 0.35 ms
TS15C 60 230 1152 304 1152 Hz 0.43 ms
TS20C, NS 150 570 395 104 988 Hz 0.51 ms
TS30C, 200 760 276 73 920 Hz 0.54 ms
Interm. duty
250 945 1150 Hz 0.44 ms
Interm. duty 300 1135 1380 Hz 0.36 ms
With EL0300-3-13 = 100 PPG scaler
TS10C 40 150 100 26  67 Hz 1.30 ms
TS15C 60 230 100 26 100 Hz 1.30 ms
TS20C, NS 150 570 100 26 250 Hz 1.30 ms
TS30C, 200 760 100 26 333 Hz 1.30 ms
Interm. duty 231 875 385 Hz 1.30 ms
If higher flow rates occur, use EL0300-3-18 (see below)
With EL0300-3-18 = 10 PPL scaler
TS10C 40 150 37.9 10  25 Hz 2.50 ms
TS15C 60 230 37.9 10 38 Hz 2.50 ms
TS20C, NS 150 570 37.9 10 95 Hz 2.50 ms
TS30C, 200 760 37.9 10 126 Hz 2.50 ms
Interm. duty 250 945 158 Hz 2.50 ms
Interm. duty
300 1135 189 Hz 2.50 ms
EMR 3
Please refer to FPP261 for other registers.
ELNC
400 Hz
CAPACITY K Factor
Frequency (Hz) &
Pulse ON time at
100% of model cap.
1667 Hz