Yamaha EMX100CD - Manual (Page 24)

E-16
TRACK
TOTAL
USER TAPE 1 ROGRAM
OGIC HALL
PROG
VOLUME
OVER 15
1 2 3 4
7 8 9 10
13 14 15
5
11
6
12
TRACK
USER TAPE 1 PROGRAM
OGIC HALL
PROG
VOLUME
OVER 15
1 2 3 4
7 8 9 10
13 14 15
5
11
6
12
COMPACT DISC PLAYER OPERATION
Program play
You can program up to 20 tracks in any desired order.
1
Load discs and close the disc table.
2
When in the stop mode, press the PROG button to
prepare for programming.
*
“PROG” and “P-01” will light up on the display, and all
track numbers on the selected disc begin flashing.
3
If necessary, select a desired disc by pressing the DISC
SKIP button.
*
Just after you changes the disc, this unit reads the
contents of the newly selected disc for a few seconds.
During this internal operation, if you go on to the next
step, “WAIT” appears on the display and your
operation is canceled.
4
Use the track number input buttons to select the desired
track number.
*
The selected track number and the total play time of
the programmed tracks will light up on the display, and
soon it is replaced by the display of the next playback
order. Programmed track numbers on the selected disc
will stop flashing and light up on the music calendar.
* Pressing the TIME button displays the total play time of
the programmed tracks for about 1 second, and then it
is replaced by the display of the next playback order.
* For example, to choose selection 12
(1) Press the “+10” button.
(2) Within 3 seconds, press the “2” button.
5
Repeat steps 3 and 4 for any other track. Up to 20 tracks
can be programmed.
6
Press the play/pause / button to start playback of
programmed tracks.
Notes
•
It is also possible to program a sequence of tracks while
looking at the list of tracks on the surface of the disc
before closing the disc table.
•
During playback or pause, programming is not possible.
•
If the total time of the programmed tracks becomes 100
minutes or more, the highest position of a figure will not be
displayed.
•
The total time of the programmed tracks will not be
displayed, if track number 16 or higher is programmed.
•
Skip search can be performed during playback, but only
within the range of the programmed tracks.
• Manual search can be performed during playback to
search all tracks, including unprogrammed tracks.
• If programs are made selecting tracks from more than one
disc, pressing the DISC CHANGE button is useless during
program play.
1
1
2
2
3
3
4
4
5
5
TIME
A
DISC SKIP
PROG
B C D
+ I0
E
OPEN/CLOSE RANDOM REPEAT MODE
6
6
7
7
8
8
9 0
CD
PRESET
TUNER
STOP
INPUT
PLAY/PAUSE
LEVEL MUSIC
TEST FLAT CENTER/REAR
/DELAY
ECHO PROGRAM USER
POWER
DISPLAY SLEEP
VOLUME
CD CHANGER RECEIVER EMX–100CD
PHONES
POWER
DISC 1 2 3
PROGRAM
ECHO ECHO
MUSIC
USER MEMORY
INPUT SELECTOR VCR/LD-TV/CD/TUNER/TAPE•MD/AUX VOLUME
RANDOM
DISPLAY MIC
MIN MAX
MIC MIXING
REPEAT TIME MEMORY AUTO/MAN'L
HOUR PRESET/TUNING/BAND A/B/C/D/E MIN TIME ADJ TIMER
OPEN/
CLOSE
DISC
CHANGE
Display information during programming
Playback order
Music calendar Selected disc
Selected track number Total playing time
1
2
3
TIME
4
1
6
6