Panasonic HD1700pe - Manual (Page 88)

88
Setup menus
The underlining (__) denotes the factory setting mode.
No./Item Description of setting
300
IN/OUT DEL
For selecting the operation to be performed when
an edit point has been set incorrectly (when the
OUT point comes before the IN point).
0000 MANU:
Editing is not performed unless the illegal edit
point is cleared or set properly.
0001 AUTO:
The edit point which had already been input is
cleared automatically.
301
NEGA FLASH
For selecting whether to show a negative display
(time code display area) when the IN point is
greater than the OUT point.
0000 OFF:
A negative display is not shown.
0001 ON:
A negative display is shown.
No./Item Description of setting
302
CONFI EDIT
For selecting whether to perform simultaneous
playback during editing.
0000 OFF: Simultaneous playback is not
performed.
0001 ON: Simultaneous playback is
performed.
Simultaneous playback takes effect when TAPE is
selected as the F1 key
setting on the
menu. Refer to setup menu item No.140 as
well.
OUTPUT
303* 1
AUD EDIT
IN
For selecting how to connect the digital audio
edit IN points.
0000 CUT: Cut processing
0001 FADE: V-fade processing
304* 1
AUD EDIT
OUT
For selecting how to connect the digital audio
edit OUT points.
0000 CUT: Cut processing
0001 FADE: V-fade processing
305
AUTO ENTRY
For selecting whether to register the IN points
using the PREROLL button in cases where
the IN points have not been registered.
0000 DIS: The IN points are not
registered.
0001 ENA: The IN points are registered.
306* 1
CF ADJ SEL
For selecting the deck whose the color
framing is to be adjusted during deck-to-deck
editing.
0000 PLAYER:
The player’s IN and OUT points are adjusted
(using the recorder as the reference).
0001 RECORD:
The recorder’s IN and OUT points are adjusted
(using the player as the reference).
307
AFTER
CUE-UP
For selecting the VTR’s mode upon
completion of the cue-up operation.
0000 STOP:
The VTR is set to the STOP mode.
0001 STILL:
The VTR is set to the still picture (SHTL STILL)
mode.
0002 STILL2:
The VTR is set to the still picture (VAR STILL)
mode.
308
VAR FWD
MAX
For setting the maximum speed of VAR FWD.
0000 i 4.9: i 4.9 times normal tape speed
0001 i 2: i 2 times normal tape speed
(i1.85 times normal tape
speed for formats other than
DVCPRO HD-LP)
0002 i 1: i 1 times normal tape speed
• At any setting other than 0 (i4.9), phase adjustments
cannot be conducted from the editing controller.
• Depending on the format used, the actual tape
running speed differs slightly from what is indicated
by the superimposed display.
310
JOG FWD
MAX
For setting the maximum speed of JOG FWD.
0000 i 4.9: i 4.9 times normal tape speed
0001 i 2: i 2 times normal tape speed
(i1.85 times normal tape
speed for formats other than
DVCPRO HD-LP)
0002 i 1: i 1 times normal tape speed
At any setting other than 0 (i4.9), phase adjustments
cannot be conducted from the editing controller which
performs these adjustments by the JOG command.
311
JOG REV MAX
For setting the maximum speed of JOG REV.
0000 j 4.9: j 4.9 times normal tape speed
0001 j 2: j 2 times normal tape speed
(j1.85 times normal tape
speed for formats other than
DVCPRO HD-LP)
0002 j 1: j 1 times normal tape speed
312
POSTROLL
TM
For setting the postroll time.
Any time from 0 to 5 seconds can be set in 1-
second increments.
0000 0s
0001 1s
0002 2s
0003 3s
0004 4s
0005 5s
309
VAR REV MAX
For setting the maximum speed of VAR REV.
0000 j 4.9: j 4.9 times normal tape speed
0001 j 2 : j 2 times normal tape speed
(j1.85 times normal tape
speed for formats other than
DVCPRO HD-LP)
0002 j 1: j 1 times normal tape speed
Depending on the format used, the actual tape running
speed differs slightly from what is indicated by the
superimposed display
.
*1: This item is not displayed when the 23/24 Hz or 25 Hz (HD or
SD) mode has been selected as the system menu item No.25
(SYSTEM FREQ) setting.