Silvercrest KH 2380 - Manual (Page 16)

16 GB/IE
EON: (ON / OFF): EON function on or off.
• Turn the “SEL / VOL” control knob
cp until the
display 3 reads [EON ON]; the EON function
is now activated.
• Turn the “SEL / VOL” control knob cp until the
display 3 reads [EON OFF]; the EON function is
now deactivated.
DSP: (NONE / CLAS / ROCK / POP / FLAT):
Selection of an acoustic pattern for various
playback styles of music and language with
preset bass and treble levels.
• Turn the “SEL / VOL” control knob cp until
[NONE] appears in the display window 3 . The
acoustic pattern of your setting for [BAS] and
[TRE] is selected.
• Turn the “SEL / VOL” control knob cp until
[CLAS] appears in the display window 3 ; the
acoustic pattern for classical music is selected.
• Turn the “SEL / VOL” control knob cp until
[ROCK] appears in the display window 3 ; the
acoustic pattern for rock music is selected.
• Turn the “SEL / VOL” control knob cp until
[POP] appears in the display window 3 ; the
acoustic pattern for pop music is selected.
• Turn the “SEL / VOL” control knob cp until
[FLAT] appears in the display window 3 ; the
acoustic pattern for speech is selected.
Your settings are automatically stored.
The device automatically changes back to playback
mode after five seconds.
L Adjusting volume
• Increase the volume by turning the “SEL / VOL”
control knob cp clockwise.
• Reduce the volume by turning the “SEL / VOL”
control knob cp counter clockwise.
Mute Function
The mute function enables you to turn off the
loudspeakers.
• Press the
MU button cl . Playback is muted
and [MUTE] appears in the display window 3 .
• Press the MU button cl again. Playback
continues as before the MUTE function was
activated and
[MUTE] disappears from the
display window 3 .
Loudness Function
The loudness function increases the playback level
of the bass sounds when the volume is low.
• Press the
• LD / MD button bu and keep it held
down for approximately 2 seconds. The loudness
function is activated,
[LOUD ON] appears in
the display window 7 followed by [LOUD].
• Turn the “SEL / VOL” control knob co again.
[LOUD OFF] appears in the display window.
• Press the
• LD / MD button bu again and keep
it held down for approximately 2 seconds. The
loudness function is deactivated,
[LOUD OFF]
appears in the display window 3 followed by
[LOUD].
L Setting the 3-Band PLL Tuner
Press the
• LD / MD button bu until TUNER appears
in the display window 3 .
You can select 3 x FM frequency bands (FM1, FM2
and FM3), 2 x medium wave frequency bands (MW1
and MW2) and 1 x long wave frequency band. Each
frequency band has six presets on which you can
store radio stations.
• Press the
BD / ENT button bs and select the
frequency band you wish to receive. In the display
window
3 you will now see the designation of
the frequency band (e.g. [FM2]), the frequency
(e.g. [99.20]) of a radio station that is being
received or the programme ID during stereo
reception and
[TP] for traffic information.
Automatic Station Search
• Start the station search at lower frequencies
by briefly pressing the
9
button 6 . The
tuner automatically plays back the next radio
station that it receives and shows the
information in the display window
3 .
• Start the station search at higher frequencies
by briefly pressing the
:
button 5 . The
tuner automatically plays back the next radio
station that it receives.
Operation
KH2380_Content_UK.indd 16 12.09.2006 11:57:13 Uhr