Intelligent Motion Systems MDrive34AC Plus2-65 - Manual

General Specifications
Electrical Specifications
Input Voltage Range (120 VAC MDrive) 95 to 132 VAC @ 50/60 Hz
Input Current (120 VAC MDrive) 4.2 Amps
Input Voltage Range (240 VAC MDrive) 95 to 264 VAC @ 50/60 Hz
Input Current (240 VAC MDrive) 2.1 Amps
Aux-Logic Input Voltage +12 to +24 VDC
Aux-Logic Input Current 230 mA Max
Environmental Specifications
Operating Temperature
(non-condensing) Heat Sink -40°C to +75°C
Motor -40°C to +90°C
Sealing (Plus 2 -65 Only) IP-65 Compliant
I/O Specifications
General Purpose I/O - Number and Type
I/O Points 1-4, 9-12
8 programmable I/O Points - sinking
or sourcing inputs or outputs.
General Purpose I/O - Electrical
Inputs TTL, +5 to +24 VDC
Sinking Outputs +5 to +24 VDC
Sourcing Outputs +12 to +24 VDC
Output Sink Current up to 600 mA
Logic Threshold (Logic 0) < 0.8 VDC
Logic Threshold (Logic 1) > 2.2 VDC
Protection (Sinking) Over Temp, Short Circuit
Protection (Sourcing)
Transient Over Voltage, Inductive
Clamp
Analog Input
Resolution 10 Bit
Range (Voltage Mode) 0 to +5 VDC, 0 to +10 VDC
Range (Current Mode) 4 to 20 mA, 0 to 20mA
Clock I/O
Types
Step/Direction, Up/Down,
Quadrature
Logic Threshold
TTL Input, TTL Output (with 2 kΩ
Load to Ground)
Trip Output/Capture Input
Logic Threshold
TTL Input, TTL Output (with 2 kΩ
Load to Ground)
Communications Specifications
Protocol RS-422/RS-485
BAUD Rate 4.8k, 9.6k, 19.2k, 38.4k, 115.2 kbps
CANopen Option
Protocol CAN 2.0B Active
Communications Profile CiA DS-301
BAUD Rate
Note: 800 kbps not supported by the MD-CC500-000
USB to CANopen dongle.
10, 20, 50, 125, 250, 500, 800
kBit/s, 1MBit/s (default)
Protection Specifications
Thermal
Internal Fuse (Line-Neutral Systems Only, Line-Line Systems Require External Fusing
Motion Specifications
Microstep Resolution - Open Loop
Number of Resolutions 20
Available Microsteps Per Revolution
200 400 800 1000 1600 2000 3200 5000 6400 10000
12800 20000 25000 25600 40000 50000 51200 36000 1 21600 2 25400 3
1=0.01 deg/µstep 2=1 arc minute/µstep 3=0.001 mm/µstep
Software Specifications
Program Storage Type/Size Flash/6384 Bytes
User Program Labels and Variables 192
Party Mode Addresses 62
MDrive34AC Plus Motion Control Quick Reference R070208
Mechanical Specifications
Dimensions in inches (mm)
Motor Length LMAX1
(Single Shaft or
Internal Encoder)
LMAX2
(Control Knob)
Single 6.1 (155.0) 7.1 (180.4)
Double 6.9 (174.3) 7.9 (199.7)
Triple 8.4 (214.3) 9.4 (239.79)
LMAX1
LMAX2
1.46
(37.0)
0.87
(22.0)
Ш 0.55
(Ш 14.0)
0.40
(10.1)
0.08
(2.0)
2.70
(68.4)
3.38 SQ.
(85.8 SQ.)
5.76
(146.2)
6.47
(164.2)
2.74 SQ.
(69.58 SQ.) Ш 2.87
(Ш 73.0)
3.46
(87.8)
0.63
(16.0)
All documentation, software and resources are available online at:
http://www.imshome.com/mdrive34acplus_mdi.html
Quick Reference MDrive34AC Plus 2 -65
Motion Control
Notes and Warnings
Installation, configuration and maintenance must be carried out by qualified
technicians only. You must have detailed information to be able to carry out this
work. This information can be found in the user manuals.
• Unexpected dangers may be encountered when working with this product!
• Incorrect use may destroy this product and connected components!
The user manuals are not included. You can obtain them from the Internet at:
http://www.imshome.com/mdrive34acplus_mdi.html.
Required for Setup*
PC running Microsoft • ® Windows XP Service Pack 2 or greater.
IMS Terminal integrated program editor and terminal emulator. (Available •
online)
IMS MD-CS200-000 or equvalent Lumberg Euro AC cable for AC line.
•
(Requred for UL)
RS-422/485 communications interface. (Recommended: IMS MD-
•
CC401-001 Communication Converter) or CANopen communications
converter. (Recommend MD-CC500-000)
Depending on your MDrivePlus connectors configuration, you may also need:
I/O and Power interface to 19-pin M23 circularp connector. (Recom- •
mended: IMS MD-CS100-000 or MD-CS101-000 Prototype Development
Cordset)
* If you purchased your MDrivePlus with a QuickStart Kit, you have received all
of the connecting cables needed for initial functional setup and system testing.
Getting Started
All documentation, software and resources are available online at:
http://www.imshome.com/mdrive34acplus_mdi.html
Connecting Power and I/O
Your MDrivePlus is configured with power and I/O combined on separate
connectors. Please refer to the opposite side of this document for connecting
details and available IMS connectivity options including Prototype Development
Cables and Mating Connector Kits.
Connecting Communications — RS-422/485
Connect IMS RS-422/485 communications converter to MDrivePlus and 1.
PC.
Install the communication converter drivers onto PC (available online).
2.
Install and open IMS Terminal. 3.
Apply power to MDrivePlus. 4.
Within IMS Terminal, Click into the Terminal Window (shown below). 5.
Key in CTRL+C. The MDrivePlus sign-on message: “Copyright 2001-2008 6.
by Intelligent Motion Systems, Inc.” should appear, verifying that com-
munications is active.
Connecting Communications — CANopen
A “Getting Started” tutorial using the IMS CANopen Tester GUI with the
MD-CC500-000 USB to CANopen dongle is available online at:
http://www.imshome.com/canopen_gs.html.
Program Editor
Window
Terminal Emulator
Window
>Copyright 2001-2008 by Intelligent Motion Systems. Inc.