Sr in rc-5 sw r r sr l sl pre out sbl sbr, Out rc, Cdss/vcr2 dvd – Marantz SR5500 User Manual
Page 17: Out in c out multi, Am gnd, Monitor, Out tv vcr1 monitor, Out in c dvd tv out multi, Rc-5 in out
ENGLISH
14
ADVANCED CONNECTING
CONNECTING MULTI CHANNEL AUDIO SOURCE
The 7.1CH INPUT jacks are for multichannel
audio source such as a SACD multichannel
player, DVD audio player or external decoder.
If you use these jacks, switch on the 7.1CH INPUT
and set the 7.1CH INPUT level by using the
SETUP MAIN MENU. See page 28.
CONNECTING AN EXTERNAL POWER AMPLIFIER
The PREOUT jacks are for connecting external
power amplifiers.
Be sure to connect each speaker to the corresponding
external power amplifier.
POWER
AMPLIFER
DVD AUDIO PLAYER
or
SACD MULTI CHANNEL
PLAYER
Center
Front
Left
Front
Right
Surround
Left
Surround
Right
Subwoofer
Surround
Back Left
CONNECTING THE REMOTE CONTROL JACKS
MD DECK
CD RECORDER
q
You can control other Marantz products through
this unit with the remote control by connecting the
REMOTE CONTROL terminals on each unit.
The signal transmitted from the remote control is
received by the remote sensor on this unit. Then
the signal is sent to the connected device through
this terminal. Therefore you need to aim the
remote signal only to the unit. Also, if a Marantz
power amplifier (some models excluded) is
connected to one of these terminals, the power
amplifier’s, power switch is synchronized with this
unit’s power switch.
Set the REMOTE CONTROL SWITCH on the units,
other than the main unit to EXT.(EXTERNAL) for
this feature.
CD PLAYER
OPTION
w
Whenever external infrared sensors or similar
devices are connected to RC-5 IN of the SR5500,
be sure to always disable operation of the infrared
sensor on the main unit by using the following
procedure.
1.
Hold down the
7.1CH INPUT
button and
MENU
button on the front panel at the same
time for five seconds.
2.
The setting “IR=ENABLE” is shown on the FL
DISPLAY.
3.
Press the or cursor button to change this
to “IR=DISABLE”.
4.
Press the
ENTER
button. Once this setting is
made, the infrared sensor on the main unit is
disabled.
Note:
• Be sure to set to “IR=ENABLE” when external
infrared sensors or similar devices are not
connected. Otherwise, the main unit will be
unable to receive remote control commands.
5.
To restore the original setting, perform steps 1
to 4 to set to “IR=ENABLE”.
Surround
Back Right
COMPONENT VIDEO
CB/PB
CR/PR
CR/PR
CR/PR
CB/PB
CB/PB
INPUT-1
Y
MONITOR OUT
INPUT-2
Y
MONITOR
(AUX2)
OUT
TV
VCR1
R
OUT
IN
TAPE
CDR/MD
OUT
SW
OUT
IN
SBL
SBR
SL
L
IN
IN
7.1CH
AUDIO
SR
IN
RC-5
SW
R
R
SR
L
SL
PRE
OUT
SBL
SBR
MULTI
OUT
RC
C
C
DSS/VCR2
DVD
S-VIDEO
OUT
IN
C
OUT
MULTI
MODEL NO
SW
SBL
SBR
SL
L
IN
7.1CH
SR
SW
R
R
SR
L
SL
PRE
OUT
SBL
SBR
C
C
L
R
FRONT SURR.
SURR.
BACK
SUB
WOOFER
CENTER
L
R
FRONT SURR.
SURR.
BACK
SUB
WOOFER
CENTER
R
L
R
L
R
L
L
R
R L
L
R
L
R
R L
R L
R L
R L
R L
AM
GND
ANTENNA
COMPONENT VIDEO
FM (75
Ω
)
CB/PB
CR/PR
CR/PR
CR/PR
CB/PB
CB/PB
INPUT-1
Y
Y
MONITOR OUT
INPUT-2
Y
COAX.
4
2
OPT.
1
3
DIGITAL OUT
DIGITAL IN
MONITOR
(AUX2)
OUT
TV
VCR1
MONITOR
VIDEO
OUT
IN
IN
OUT
TAPE
CDR/MD
OUT
SW
OUT
IN
CD
SBL
SBR
SL
L
IN
OUT
IN
7.1CH
AUDIO
SR
IN
RC-5
SW
R
IN
R
TV
DVD
DSS/VCR2
R
SR
L
SL
PRE
OUT
SBL
SBR
L
VCR1
VCR1
OUT
OUT
IN
DSS/VCR2
OUT
IN
MULTI
OUT
RC
RS-232C
C
DSS/VCR2
DVD
S-VIDEO
OUT
IN
C
DVD
TV
OUT
MULTI
MODEL NO
RC-5
IN
OUT
REMOTE
CONTROL
REMOTE
CONTROL
REMOTE
CONTROL
IN
OUT
IN
OUT
IN
OUT
EXTERNAL INTERNAL
EXTERNAL INTERNAL
EXTERNAL INTERNAL
1
RC OUT
2
04.8.2, 4:12 PM
Page 14