Marantz SR5500 User Manual
Page 15
ENGLISH
12
Caution:
• Be sure to use speakers with the specified
impedance as shown on the rear panel of this unit.
• To prevent damage to circuitry, do not let the bare
s p e a k e r w i r e s
touch each other
and do not let them
touch any metal
part of this unit.
• Do not touch the
speaker terminals
when the power is
on. It may cause
you to receive an electric shocks.
• Do not connect more than one speaker cable to
one speaker terminal. Doing so may damage this
unit.
Note:
• Be sure to connect the positive and negative
cables for the speaker properly. If they are miss-
connected, the signal phase will be reversed and
the signal quality will be corrupted.
CONNECTING A SUBWOOFER
Use the PRE OUT SUBWOOFER jack to connect
a powered subwoofer (power amplifier built in).
If your subwoofer is a passive type (power
amplifier is not built in), connect a monaural power
amplifier to the PRE OUT SUBWOOFER jack and
connect the subwoofer to the amplifier.
CONNECTING AUDIO COMPONENTS
The output audio signal from the TAPE OUT jack
and the CD-R/MD OUT jack is the same signal
which is currently selected.
Caution:
• Do not connect this unit and other components to
mains power until all connections between
components have been completed.
Notes:
• Insert all plugs and connectors securely.
Incomplete connections may make noise.
• Be sure to connect the left and right channels
properly.
Red connectors are for the R (right) channel, and
white connectors are for the L (left) channel.
• Be sure to connect input and output properly.
• Refer to the instructions for each component that
is connected to this unit.
• Do not bind audio/video connection cables with
power cords and speaker cables this will result in
generating a hum or other noise.
CONNECTING DIGITAL AUDIO COMPONENTS
• There are 4 digital inputs, 2 coaxial jacks and 2
optical jacks, on the rear panel. You can use
these jacks to input PCM, Dolby Digital and DTS
bitstream signals from a CD, DVD, or other
digital source components.
• There is one digital output coaxial jack and one
optical output jack on the rear panel. These
jacks can be connected to a CD recorder-, or a
MD deck inputs, respectively.
• Refer to the instructions for each component. To
setup the digital audio format of DVD player, or
other digital source’s connected to digital input
jacks.
• Use fiber optical cables (optical) for DIG-1,2
input jacks. Use 75 ohms coaxial cables (for
digital audio or video) for DIG-3, 4 input jacks.
• You can designate the input for each digital
input/output jacks according to your component.
See page 18.
CD RECORDER / MD DECK
CD PLAYER
TAPE DECK
ANALOG AUDIO
DIGITAL AUDIO
(COAXIAL)
DIGITAL AUDIO
(OPTICAL)
Notes:
• There is no Dolby Digital RF input jack. Please
use an external RF demodulator Dolby Digital
decoder when connecting the Dolby Digital RF
output jack of the video disc player to the digital
input jack.
• The digital signal jacks on this unit conform to the
EIA standard. If you use a cable that does not
conform to this standard, this unit may not
function properly.
• Each type of audio jack works independently.
Signals input through the digital and analog jacks
are output through the corresponding digital and
analog jacks, respectively.
AM
GND
ANTENNA
COMPONENT VIDEO
FM (75
Ω
)
CB/PB
CR/PR
CR/PR
CR/PR
CB/PB
CB/PB
INPUT-1
Y
Y
MONITOR OUT
INPUT-2
Y
COAX.
4
2
OPT.
1
3
DIGITAL OUT
DIGITAL IN
MONITOR
(AUX2)
OUT
TV
VCR1
MONITOR
VIDEO
OUT
IN
IN
OUT
TAPE
CDR/MD
OUT
SW
OUT
IN
CD
SBL
SBR
SL
L
IN
OUT
IN
7.1CH
AUDIO
SR
IN
RC-5
SW
R
IN
R
TV
DVD
DSS/VCR2
R
SR
L
SL
PRE
OUT
SBL
SBR
L
VCR1
VCR1
OUT
OUT
IN
DSS/VCR2
OUT
IN
MULTI
OUT
RC
RS-232C
C
DSS/VCR2
DVD
S-VIDEO
OUT
IN
C
DVD
TV
OUT
MULTI
MODE
AUDIO
TAPE
IN
CD
CDR/MD
OUT
IN
OUT
R
L
OPT.
1
DIGITAL OUT
DIGITAL IN
4
OUT IN
L
R
L
R
OUT
L
R
L R
L R
L R
R
L
R
L
R
L
OUT IN
L
R
L
R
DIGITAL
INPUT
DIGITAL
OUTPUT
DIGITAL
OUTPUT
R L
R L
R L
R
L
L
R
04.8.2, 4:12 PM
Page 12