Marantz SA-11S1 - Manual (Page 17)

13
ENGLISH
CHANGING THE TEXT BRIGHTNESS ON
THE LCD (LCD CONTRAST ADJUSTMENT)
Changing procedure (Changes can be made from
the main unit when operation is stopped.)
q If playback is in progress, press the
STOP
button to stop playback.
w Hold down the PAUSE button on the main unit
for at least two seconds. (This operation does not
work on the remote control.)
After holding down the button for two seconds,
the current contrast value is displayed. Within two
seconds while it is displayed, press the
button to increase the contrast, or press the
button to reduce the contrast. Changes
can be made to the contrast level over the entire
range (+8 to -8).
If the
or button is not pressed
within two seconds, the contrast is automatically
set to the currently displayed level.
Display example: Contrast +-0
e Pressing the STOP button while changing the
setting returns to the default setting (+-0).
* Any changes made to the LCD contrast setting
are retained even when the power is turned off.
TURNING OFF THE DISPLAY AND
ILLUMINATION (DISPLAY OPERATION)
This function is used to turn the LCD and illumination
lamps (blue) on and off. (Two display statuses are
available.)
1. Mode where LCD and illumination lamp (blue) turn
on
Each time the DISPLAY button is pressed during
playback, the LCD and illumination lamp (blue)
switch on and off.
When Display Off is set, the Display Off indicator
(red) lights up.
* When any related button is pressed (such as
when the OPEN/CLOSE button, STOP
button, or button is used), the display is
automatically turned on, but the Display Off
indicator (red) remains lit. If a track is started in
this state, the display is automatically turned off
two seconds later.
* When a track is stopped, the Display Off
indicator (red) and illumination lamp (blue) light
up alternately.
2. Setting for turning on only LCD (illumination lamp
(blue) remains off)
In the default state, the illumination lamp (blue) is
lit. In this state, the illumination lamp (blue)
remains off regardless of whether the LCD is
turned on or off.
Changing procedure (Changes can be made
when operation is stopped.)
q If playback is in progress, press the STOP
button to stop playback. To make the setting, hold
down the
DISPLAY button for at least two
seconds from the remote control (RC-11SAS1).
w If the illumination lamp (blue) is lit, it is turned off
and is set off. To change the setting from off to
on, hold down the same operation
DISPLAY
button for at least two seconds to turn on.
* The illumination lamp (blue) off setting is retained
even when the power is turned off, and this setting
remains until the setting is changed to the on
setting.
* The LCD display on/off setting is not retained when
the power is turned off. (This enables you to enjoy
operation each time you use it.)
TIMER PLAY
This unit can perform timer play by cooperating with
your audio timer.
Connect this unit’s power cord to the audio timer’s
power socket and the timer’s power cord to power
outlet.
* For connection to audio timer and it’s operation,
please refer to the instruction manual of your audio
timer.
Setting method of Timer Play
q Press POWER switch to turn ON the power.
w Insert the disc to be played.
* In timer play mode, tracks are played normally.
e Set the audio timer.
Audio Timer
ABOUT BALANCED JACKS
q The balanced output connector uses a XLR
connector.
w The XLR connector for professional use is
internally wired in either of the following two
systems.
1. USA system (Pin w = COLD, Pin e = HOT)
w q
e
GND
HOT
COLD
2. European system (Pin w = HOT, Pin e = COLD)
w q
e
GND
COLD
HOT
e The SA-11S1 uses the 1. USA system.
When a preamp or main amplifier adopting the
European system is connected using a cable with
XLR balanced connectors, the reproduced signal
may be inverted of phase.
In this case, correct the wiring of the one of the
XLR connectors on the extremities of the cable
to the USA system by exchanging the connections
of pins w and e. This will make it possible to
play the signal with the correct phase.
04.8.3, 4:42 AM Page 13