Marantz SA-11S1 - Manual (Page 13)

9
ENGLISH
OPERATION
* In this instruction manual, some operations can only be performed with the remote control. For
operations that can be performed with buttons both on the main unit and on the remote control, the
button names are shown in the
mark. And for operations that can only be performed with
buttons on the remote control, the button names are shown in the mark.
CONNECTING THE POWER SUPPLY
1 Plug the power cable into AC IN jack on the back
panel.
2 Turn on the power switch of the audio unit
(amplifier, etc.) that is connected with this unit.
Set the selector on the connected unit to this unit.
3 Plug the power cable into an AC outlet.
NORMAL PLAYBACK
SUPER AUDIO CD PLAYER PLAYBACK
PAUSE
STOP
PLAY OPEN/
SOUND POWER ON/OFF
SUPER AUDIO CD PLAYER SA-11S1 CLOSE
MODE
G M A H
DISPLAY OFF
q Press POWER switch to turn on.
LCD
The display cycles from TOC Reading → No
Disc (when no disc is loaded) → Super Audio
CD (when the start sound mode setting is Super
Audio CD).
w Press the OPEN/CLOSE button
The disc tray comes out. Place the disc with label
side up on the tray.
To play a single (8cm) CD, place the disc with
the indentation at the center of the tray.
e Press OPEN/CLOSE button.
r Press PLAY button.
Disc type is automatically detected and playback
is started. Track number and track elapsed
time(minute, second) appear on the display.
* For Super Audio CD/CD hybrid-layer discs (See
page 2), the layer that is set in the start sound
mode (See page 10) is played. To change the
layer, use the
SOUND MODE button. (See page
9)
(Exp.:Track 6, Elapsed time 2 min 8 sec)
Playback automatically stops at the end of the
final track.
Number of current track Minutes Seconds
Remaining track numbers
AC IN
To start playback form the first track
Press PLAY button.
To stop playback
Press STOP button.
To eject disc
Press OPEN/CLOSE button to open the disc tray
and take the disc off. Press the button again to close
the tray.
Disc tray must be closed when the unit is not be
used.
To pause playback
Press PAUSE button.
PAUSE indicator will light and playback is paused at
the point that the button is pressed. To restart
playback, press
PAUSE button again or press
PLAY button.
To change time display
Press the TIME button on the remote control.
Each time TIME button is pressed, display will
change in the following order. “Track elapsed time”
→ “Track remaining time” → “Total remaining time”
→ “Track elapsed time”.
• Track remaining time
(The remaining playing time from the playing
point to the end of the current track)
• Total remaining time
(The remaining playing time from the playing
point to the end of the last track)
* If TIME button is pressed when Super Audio CD
disc that supports text is in use, time display is given
priority and the text information will not be displayed
afterward. To see the text information, press
TEXT
button.
SWITCHING SOUND MODE (SUPER AUDIO CD)
PAUSE
STOP
PLAY OPEN/
SOUND POWER ON/OFF
SUPER AUDIO CD PLAYER SA-11S1 CLOSE
MODE
DISPLAY OFF
q Press SOUND MODE button in stop mode
(not playing).
The currently selected layer or area is shown on
the LCD. (CD or Super Audio CD)
If
SOUND MODE button is pressed again, a
playable layer or area will be shown, and the layer
or area will be switched to new one.
* When layer or area is switched, TOC will be
read again.
* The sound mode cannot be changed for Audio
CDs and discs with only a Super Audio CD
area.
* The sound mode on hybrid layer discs will be
changed in the following order.
Super Audio CD stereo area
→ CD layer →
Super Audio CD stereo area
* Sound mode can be selected while the tray is
open. Select a desired layer or area and press
PLAY button then the tray will close and
playback will be started.
w Press the SOUND MODE button during
playback.
The currently selected layer or area is shown on
the LCD. (CD or Super Audio CD)
If
SOUND MODE button is pressed again, the
playback is stopped, and the layer or area will
be switched to new one.
When you want to listen at that area, press
PLAY button again. The playback will be
started.
“–” is displayed
“ R E M A I N ”
is displayed
“–” is displayed
“TOTAL REMAIN”
is displayed
SOUND MODE Button
04.8.3, 4:42 AM Page 9