T.tone menu off set up/ 1. 2, T.tone menu off set up/ 2. 6. 3, T.tone menu off set up/ 1. 3. 4. 2 – Marantz SR5600 User Manual
Page 12
ENGLISH
8
RESETTING THE ALL CODE
1.
Press and hold down the any
Function
Selector
button and press
SETUP
button until
the indicator blinking twice.
2.
Press the code
9
-
8
-
1
.
The indicator will blink twice.
Then, RC5500SR will return to the factory
preset code.
Note:
• After this procedure, the selected function button
is set initial code and other function buttons are
set initial code too.
Once you have found and the codes for your various
appliances, you may want to write them down here.
TV
VCR
DSS
DVD
CD
TAPE
CDR
MD
SCANNING THE CODE TABLE
1.
Switch on the appliance which should be
controlled.
2.
Press and hold down the
Function Selector
button for appliance which should be
controlled and press
SETUP
button
until the
indicator blinking twice.
3.
Press the code
9
-
9
-
1
.
The indicator will blink twice.
4.
Aim the remote control at the appliance and
slowly alternate between pressing
POWER
button
and the
Function Selector
button for
the appliance.
5.
Stop when the appliance turns off.
6.
Press
SETUP
button once to lock in the code.
CHECKING THE CODE
1.
Press and hold down the
Function Selector
button for appliance which should be
controlled and press
SETUP
button until the
indicator blinking twice.
2.
Press the code
9
-
9
-
0
.
The indicator will blink twice.
3.
To view the code for first digit, press
1
once.
Wait 3 seconds, count the indicator blinks
(e.g. 3 blinks = 3) and write down the number.
Note:
• If a code digit is “0”, the indicator will not blink.
4.
Repeat step 3 three more times for remaining
digits. Use
2
for the second digit,
3
for the
third digit, and
4
for the fourth digit.
PROGRAMMING THE REMOTE
CONTROLLER
The remote controller RC5500SR must be
programmed to use the codes for your appliances
of different brands. This is done by keying in a 4-
digit code or by scanning the codes until the
correct one is found. We recommend to using the
4-digit code. This mode is faster and more reliable.
The code scanning method should be used only if
y o u c a n n o t f i n d t h e c o d e f o r o n e o f y o u r
appliances. The codes are listed at the end of this
book.
Important:
• Use the remote control buttons for programming,
not the buttons of the receiver or other appliances.
• Some codes may be not match your equipment.
In this case, your equipment cannot be controlled
with this remote controller.
PROGRAMMING WITH THE 4-DIGIT CODE
1.
Press and hold down the
Function Selector
button for the appliance which should be
controlled and press
SETUP
button
until the
indicator blinks twice.
2.
Press the 4-digit code for appliance (code
table at the end of this book)
3.
When the procedure is successful, the indicator
will blink twice.
Note:
• If the indicator did not blink twice, then repeat
steps 1 through 2 and try entering the same code
again.
¤1
PURE DIRECT button
When this button is pressed, the tone control
circuit is bypassed.
¤2
SETUP / T.TONE button
(when AMP mode is selected)
Used to enter the test tone menu.
¤3
OSD button
(when AMP mode is selected)
When this button is pressed, the current setting is
displayed on the TV monitor.
¤4
SLEEP (sleep timer) button
This button is used for setting the sleep timer. It
can be operated the same way as the button on the
unit.
¤5
TV VOLUME UP ( ) /DOWN ( ) buttons
These buttons increase or decrease TV’s volume.
MENU
OSD
VOL.
TV
VOL.
MAIN
SLEEP
MUTE
AMP
AUX1
TUNER
CD
TAPE
CDR/MD
DVD
POWER
VCR1
DSS/VCR2
TV
1.
ENTER
PTY
SUB-T/ATT
AUDIO
INPUT/DISC+
F.DIRECT
RDS
TUNE/SEARCH
T-MODE
TREBLE
CHANNEL/SKIP
BASS
A/D
P.SCAN/V-OFF
7.1CH IN
STEREO
MCH-ST
MEMO
CLEAR
DISPLAY
NIGHT
CSII
EX/ES
VIRTUAL
DTS
PURE DIRECT
AUTO
3
2
1
6
5
4
9
8
0
7
T.TONE
MENU OFF
SET UP/
1.
2.
MENU
OSD
VOL.
TV
VOL.
MAIN
SLEEP
MUTE
AMP
TUNER
CD
TAPE
CDR/MD
DVD
POWER
VCR1
DSS/VCR2
TV
AUX1
2.
4.
4.
ENTER
TUNE/SEARCH
TREBLE
CHANNEL/SKIP
BASS
A/D
P.SCAN/V-OFF
7.1CH IN
STEREO
MCH-ST
MEMO
CLEAR
DISPLAY
NIGHT
CSII
EX/ES
VIRTUAL
DTS
PURE DIRECT
AUTO
3
2
1
6
5
4
9
8
0
7
T.TONE
MENU OFF
SET UP/
2.
6.
3.
MENU
OSD
VOL.
TV
VOL.
MAIN
SLEEP
MUTE
AMP
TUNER
CD
TAPE
CDR/MD
DVD
POWER
VCR1
DSS/VCR2
TV
AUX1
1.
ENTER
F.DIRECT
RDS
TUNE/SEARCH
T-MODE
TREBLE
CHANNEL/SKIP
BASS
A/D
P.SCAN/V-OFF
7.1CH IN
STEREO
MCH-ST
MEMO
CLEAR
DISPLAY
NIGHT
CSII
EX/ES
VIRTUAL
DTS
PURE DIRECT
AUTO
3
2
1
6
5
4
9
8
0
7
T.TONE
MENU OFF
SET UP/
1.
3.
4.
2.
MENU
OSD
VOL.
TV
VOL.
MAIN
SLEEP
MUTE
AMP
TUNER
CD
TAPE
CDR/MD
DVD
POWER
VCR1
DSS/VCR2
TV
AUX1
1.
ENTER
TUNE/SEARCH
TREBLE
CHANNEL/SKIP
BASS
A/D
P.SCAN/V-OFF
7.1CH IN
STEREO
MCH-ST
MEMO
CLEAR
DISPLAY
NIGHT
CSII
EX/ES
VIRTUAL
DTS
PURE DIRECT
AUTO
3
2
1
6
5
4
9
8
0
7
T.TONE
MENU OFF
SET UP/
MENU
OSD
1.
2.
05.6.3, 3:57 PM
Page 8