Hotpoint FFQ48 - Manual (Page 10)

10
GB
Using the display
setting the temperature
When the appliance is switched on, the standard storage
temperatures are automatically set:
• +5°C for the refrigerator compartment
• -18°C for the freezer compartment.
The temperatures that may be set are the following:
• between +2°C and +8°C for the refrigerator
compartment
• between -18°C and -26°C for the freezer compartment
To set the temperature:
1. Press the MODE button until the value flashes on the
refrigerator compartment or freezer compartment display.
2. To increase the temperature, press the ADJUST/
SELECT+ button.
To decrease the temperature, press the ADJUST/SELECT-
button.
Each time the button is pressed, the value increases by 1°C.
3. Confirm the choice by pressing the MODE button within
ten seconds: the value will stop flashing: If the choice is not
confirmed, the temperature that had been set before the
operation will appear on the display.
! The ECO function reduces the possible adjustments: from
+4°C to +6°C for the refrigerator and from -18°C to -20°C
for the freezer.
Function status
function activated (green symbol with blue inside on)
function selected (green symbol with red border
on)
function deactivated (green symbol only on)
Activating and deactivating the SUPER COOL,
ECO, SUPER FREEZE, ICE PARTY functions.
1. Press the MODE button until the desired function is
selected.
2. To activate, press the ADJUST/SELECT + button.
To deactivate, press the ADJUST/SELECT - button.
3. Confirm the choice by pressing the MODE button within
ten seconds. If the choice is not confirmed, the function
that had been set before the operation will appear on the
display.
Once the operation is over, the red border goes off.
If the function was activated: green symbol with blue inside
on. If the function was deactivated: green symbol only on.
Activating and deactivating the AQUA CARE function
1. Press the Aqua Care button. A message on the display
shows the current status of the function.
2. Press the Aqua Care button again to activate or
deactivate the function.
Water dispensing
1. Activate the Aqua Care function
2. Place the container that needs to be filled under the
outer dispenser.
3. Press the dispenser
4. Interrupt the flow by moving the container away from the
dispenser
! The Aqua Care function comes with a safety timer that
interrupts the supply if operation is continuos for more than
5 minutes. To restore operation it is necessary to press the
RESET ALARM button twice.
Setting the date and time
The settings are in series and it is not possible to adjust the
date if the time has not been set before:
1. Press the MODE button repeatedly until the SET TIME
[+/-] appears on the scrolling text display.
2. To scroll forward one hour press the ADJUST/SELECT+
button. To scroll back one hour press the ADJUST/SELECT-
button.
3. Confirm the choice by pressing the MODE button within
ten seconds. If the choice is not confirmed, the time that
had been set before the operation will appear on the
display.
Once the hours have been set, the minutes, days, months
and years can be set by following steps 1-3.
Σεττινγ τηε λανγυαγε
1. Press the MODE button repeatedly until the language
setting screen appears on the scrolling text display.
2. To scroll forward, press the ADJUST/SELECT + button.
To scroll back, press the ADJUST/SELECT - button.
3. Confirm the choice by pressing the MODE button within
ten seconds. If the choice is not confirmed, the language
that had been set before the operation will appear on the
display.
! The first time that the appliance is switched on, the
language setting request screen appears automatically on
the display: follow the described procedure.
Σωιτχη οφφ τηε σουνδ ανδ ϖισυαλ αλαρµσ
Press the RESET ALARM button: by pressing it once, the
sound alarms are switched off; by pressing it a second
time, the alarm messages are deleted from the scrolling
text on the display.
! The open door alarm is stopped by closing it (see
Troubleshooting).
! If DEMO MODE appears on the display, the appliance is
in exhibition mode, that is, it does not cool despite the fact
that the display and the internal lamp are on. To exit this
mode, press the MODE, ADJUST/SELECT+ and ADJUST/
SELECT- buttons simultaneously for at least three seconds.