Husqvarna 357XP - Manual (Page 34)

34
– English
Engine
Cylinder volume, cu.in/cm 3
Cylinder bore, inch/mm
Stroke, inch/mm
Idle speed, rpm
Power, kW/ rpm
Ignition system
Manufacture
Type of ignition system
Spark plug
Electrode gap, inch/mm
Fuel and lubrication system
Manufacturer
Carburetor type
Fuel capacity, US pint/litre
Oil pump capacity at 8500 rpm, ml/min
Oil capacity, US pint/litre
Type of oil pump
Weight
Without bar and chain, Lbs/kg
Chain/bar
Standard bar length, inches/cm
Recommended bar lengths, inches/cm
Usable cutting length, inches/cm
Chain speed at max. power, m/sec
Pitch, inch/mm
Thickness of drive link, inch/mm
Number of teeth on drive sprocket
TECHNICAL DATA
Guide bar Saw chain
Length Pitch Max nose
inch inch radius
Recommended original and replacement
bar and chain combinations
Following is a list of recommended cutting equipment for the
Husqvarna chain saw models 357XP and 359. The combinations of
powerhead, bar and chain have been investigated in accordance with
the kickback and vibration requirements of ANSI B 175.1 – 2000. The
guide bar nose radius is determined by either the maximum number
of teeth in the nose sprocket or the corresponding maximum nose
radius of a solid bar.
The following list is the chain saw manufacturers recommendations.
There may be other combinations available, which will also achieve
kickback reduction.
As we are listing the maximum guide bar nose radius, you may use a
guide bar with smaller nose radius than in our list. For guide bars of
the same length, all sprocket-nose guide bars of the same pitch and
having the same number of of sprocket teeth may be considered to
have equivalent kickback energy. A hard nose bar having the same
length and nose radius as a sprocket-nose bar may be considered to
have equivalent or less kickback energy than the sprocket-nose bar.
Low kickback saw chain is a chain which has only met the kickback
performance requirements of ANSI B 175.1 safety requirements for
gasoline-powered chain saws when tested on the representative
sample of chain saws below 3.8 cu. in. specified in ANSI B 175.1. We
recommend that you as replacement use the listed chains or "Low
kickback saw chains" which are available at your dealer.
0,050"/1,3 mm – 20BP 33LG – 72LP 72LG 72V
0,058"/1,5 mm H25 21BP 34LG H42 73LP 73LG 73V
Note: For the chains above you are free to choose between 0,050"
and 0,058" gauge drive link for the corresponding bar, see table
below.
357XP
3,5/57
1,81/46
1,34/34
2 700
3,2/ 9 600
SEM
CD
NGK BPMR 7A
Champion RCJ 7Y
0,2/0,5
Walbro
HDA175
1,27/0,7
5-15
0,69/0,38
Automatic
12,1/5,5
357XPG: 12,3/5,6
15"/38
13-24"/33-61
12-23"/31-58
21,4
0,325"/8,25
3/8"/9,52
0,058"/1,5
7
359
3,6/59
1,85/47
1,34/34
2 700
2,9/ 9 000
SEM
CD
NGK BPMR 7A
Champion RCJ 7Y
0,2/0,5
Walbro
HDA175
1,27/0,7
5-15
0,69/0,38
Automatic
12,1/5,5
359G: 12,3/5,6
15"/38
13-24"/33-61
12-23"/31-58
21,4
0,325"/8,25
3/8"/9,52
0,058"/1,5
7
´+H%y¶5\¨
13 0,325" 10T Husqvarna H30 or
15 0,325" 10T Oregon 95VP
16 0,325" 10T
18 0,325" 10T
20 0,325" 10T
13 0,325" 10T Husqvarna H25 or
15 0,325" 10T Oregon 21BP
16 0,325" 10T
18 0,325" 10T
20 0,325" 12T
15 0,325" 10T Oregon 34LG
16 0,325" 10T
18 0,325" 10T
20 0,325" 12T
15 3/8" 11T Husqvarna H42 or
16 3/8" 11T Oregon 73LP/73LG/73V
18 3/8" 11T
20 3/8" 11T
24 3/8" 11T