Husqvarna 141 - Manual (Page 6)

6
chain brake should be made by an autho-
rized servicing dealer. Take your unit to the
place of purchase if purchased from a
Husqvarna servicing dealer, or to the near-
est authorized Husqvarna service dealer.
S Tip contact in some cases may cause a
lightning fast reverse REACTION, kicking
the guide bar up and back toward the oper-
ator.
S Pinching the saw chain along the top of the
guide bar may push the guide bar rapidly
back toward the operator.
S Either of these reactions may cause you to
lose control of the saw which could result
in serious injury. Do not rely exclusively
upon the safety devices built into your saw.
WARNING: Computed kickback
angle (CKA) listed on your saw and listed in
the CKA table below represents angle of
kickback your bar and chain combinations
will have when tested in accordance with
CSA (Canadian Standards Association) and
ANSI standards. When purchasing replace-
ment bar and chain, considerations should
be given to the lower CKA values. Lower
CKA values represent safer angles to the
user, higher values indicate more angle and
higher kick energies. Computed angles rep-
resented in the non-activated column indi-
cate total energy and angle associated with-
out activation of the chain brake during
kickback. Activated angle represents chain
stopping time relative to activation angle of
chain break and resulting kick angle of saw.
In all cases lower CKA values represent a
safer operating environment for the user.
The following guide bar and chain combina-
tions meet kickback requirements of CSA
Standards Z62.1, Z62.3, & ANSI B175.1
when used on saws listed in this manual.
Use of bar and chain combinations other
than those listed is not recommended and
may not meet the CKA requirements per
standard.
Computed kickback angle (CKA) Table
BAR
Type Length CHAIN TYPE
0.050 GA 14! 91VG/VJ--- 52
MODEL
0.050 GA
16! 91VG---56
25_
136
25 _
141
141
0.050 GA 18! H 30---72
38 _
CKA WITHOUT
CHAIN BRAKE
136
0.050 GA
16! 91VG---56
25_
NOTE: If this saw is to be used for
commercial logging, a chain brake is
required and shall not be removed or
otherwise disabled to comply with Federal
OSHA Regulations for Commercial Logging.
Contact your authorized Husqvarna service
dealer.
SAFETY NOTICE: Exposure to
vibrations through prolonged use of gasoline
powered hand tools could cause blood
vessel or nerve damage in the fingers,
hands, and joints of people prone to
circulation disorders or abnormal swellings.
Prolonged use in cold weather has been
linked to blood vessel damage in otherwise
healthy people. If symptoms occur such as
numbness, pain, loss of strength, change in
skin color or texture, or loss of feeling in the
fingers, hands, or joints, discontinue the use
of this tool and seek medical attention. An
anti-vibration system does not guaranteethe
avoidance of these problems. Users who
operate power tools on a continual and
regular basis must monitor closely their
physical condition and the condition of this
tool.
SPECIAL NOTICE: Your saw is equipped
with a temperature limiting muffler and spark
arresting
screen which meets the
requirements of California Codes 4442 and
4443. All U.S. forest land and the states of
California, Idaho, Maine, Minnesota, New
Jersey, Oregon, and Washington require
many internal combustion engines to be
equipped with a spark arrestor screen by
law. If you operate a chain saw in a state or
locale where such regulations exist, you are
legally
responsible for maintaining the
operating condition of these parts. Failure to
do so is a violation of the law. Refer to the
SERVICE AND ADJUSTMENTS section for
maintenance of the Spark Arresting Screen.
Failure to follow all Safety Rules and
Precautions can result in serious injury. If
situations occur which are not covered in this
manual, use care and good judgement. If you
need assistance, contact your authorized
service dealer.
STANDARDS
CSA Z62.1 “Chain Saws -- Occupational
Health and Safety”
CSA Z62.3 “Chain Saw Kickback Occupa-
tional Health and Safety”
ANSI B175.1--2000 -- “American National
Standard for Powered Tools -- Gasoline
Powered Chain Saw -- Safety Require-
ments”