Husqvarna 340 - Manual (Page 34)

34
– English
Engine
Cylinder volume, cu.in/cm 3
Cylinder bore, inch/mm
Stroke, inch/mm
Idle speed, rpm
Power, kW/ rpm
Ignition system
Manufacture
Type of ignition system
Spark plug
Electrode gap, inch/mm
Fuel and lubrication
system
Manufacturer
Carburetor type
Fuel capacity, US pint/litre
Oil pump capacity at 8500 rpm,
ml/min
Oil capacity, US pint/litre
Type of oil pump
Weight
Without bar and chain, Lbs/kg
Chain/bar
Standard bar length,
inches/cm
Recommended bar lengths,
inches/cm
Usable cutting length,
inches/cm
Chain speed at max.
power, m/sec
Pitch, inch/mm
Thickness of drive link,
inch/mm
Number of teeth on drive
sprocket
TECHNICAL DATA
Guide bar Saw chain
Length Pitch Max nose
inch inch radius
13 0,325" 10T Husqvarna H30 or
15 0,325" 10T Oregon 95VP
16 0,325" 10T
18 0,325" 10T
15 0,325" 10T Husqvarna H25 / S24 or
16 0,325" 10T Oregon 21VB / 34LG or 34SL
18 0,325" 10T
20 0,325" 12T
Recommended original and replacement
bar and chain combinations
Following is a list of recommended cutting equipment for the Husqvarna chain
saw models 340, 345 and 350. The combinations of powerhead, bar and chain
have been investigated in accordance with the kickback and vibration
requirements of ANSI B 175.1 – 1991.
The guide bar nose radius is determined by either the maximum number of
teeth in the nose sprocket or the corresponding maximum nose radius of a
solid bar.
The following list is the chain saw manufacturers recommendations. There may
be other combinations available, which will also achieve kickback protection.
As we are listing the maximum guide bar nose radius, you may use a guide bar
with smaller nose radius than in our list. For guide bars of the same length, all
sprocket-nose guide bars of the same pitch and having the same number of of
sprocket teeth may be considered to have equivalent kickback energy. A hard
nose bar having the same length and nose radius as a sprocket-nose bar may
be considered to have equivalent or less kickback energy than the sprocket-
nose bar.
Low kickback saw chain is a chain which has only met the kickback
performance requirements of ANSI B 175.1 safety requirements for gasoline-
powered chain saws when tested on the representative sample of chain saws
below 3.8 cu. in. specified in ANSI B 175.1. We recommend that you as
replacement use the listed chains or "Low kickback saw chains" which are
available at your dealer.
340
2,5/40,8
1,57/40,0
1,28/32,5
2 700
2,0/ 9 000
FHP
CD
NGK BPMR 7A
Champion RCJ 7Y
0,020/0,5
Walbro
HDA 159
1,06/0,5
9
0,53/0,25
Automatic
10,4/4,7
13"/33
13-20"/33-50
12-19"/31-49
17,3
0,325"/8,25
0,050"/1,3
0,058"/1,5
7
345
2,7/45,0
1,65/42,0
1,28/32,5
2 700
2,2/ 9 000
FHP
CD
NGK BPMR 7A
Champion RCJ 7Y
0,020/0,5
Walbro
HDA 159
1,06/0,5
9
0,53/0,25
Automatic
10,4/4,7
13"/33
13-20"/33-50
12-19"/31-49
17,3
0,325"/8,25
0,050"/1,3
0,058"/1,5
7
350
3,0/49,4
1,73/44
1,28/32,5
2 700
2,3/ 9 000
FHP
CD
NGK BPMR 7A
Champion RCJ 7Y
0,020/0,5
Walbro
HDA 159
1,06/0,5
6-10
0,53/0,25
Automatic
10,6/4,8
13"/33
13-20"/33-50
12-19"/31-49
17,3
0,325"/8,25
0,050"/1,3
0,058"/1,5
7
0,058"/1,5 mm – – H25 S24 21VB 34LG 34SL
0,050"/1,3 mm H30 95VP – – 20VB 33LG 33SL
Note: For the chains above you are free to choose between 0,050" and
0,058" gauge drive link for the corresponding bar, see table below.
´*3Æo¶5a¨