Harbor Freight Tools PACIFIC HYDROSTAR 1/3 HP Submersible Sump Pump with Vertical Float Switch 68476 - Manual (Page 4)

Page 2 For technical questions, please call 1-800-444-3353. Sump Pump manual
Before start-up, note the following:
The pump can be connected to any shock-proof plug
which has been installed according to regulations.
The plug must have a supply voltage of 120 V~ at 60 Hz.
CAUTION
This pump has been evaluated for use with water only.
WARNING
IMPORTANT! For your own safety –
before starting to run the pump, please have
the following items checked by an expert:
1. Risk of electric shock – This pump is supplied
with a grounding conductor and grounding-type
attachment plug. To reduce the risk of
electric shock, connect only to a properly
grounded, grounding-type receptacle.
2. Risk of electric shock – This pump has not been
investigated for use in swimming pool areas.
3. The electrical connections must be
protected from moisture.
4. If there is danger of flooding, the electrical
connections must be taken to higher ground.
5. Circulation of caustic fluids, as well as the circulation
of abrasive materials, must be avoided at all costs.
6. The pump must be protected from frost.
7. The pump must be protected from running dry.
8. Access by children should also be
prevented with appropriate measures.
9. Position the Pump on a flat, level, solid surface.
Also secure the discharge pipe (not included) to a
solid surface to ensure the stability of the Pump.
10. Do not use with an extension cord.
If a GFCI-protected outlet is not close enough
to the pump, contact a licensed electrician to
install a new one. All wiring must be performed
by a licensed electrician and comply with
the National Electric Code. Do not remove
the round grounding pin from the plug.
11. Turn off power to all circuits before walking on
a wet floor. If you cannot turn power off first,
contact an electrician to turn off the power.
12. Install a backup pump and/or high water alarm
as an additional safeguard against flooding.
13. WARNING: Handling the Power Cord
on this product will expose you to lead,
a chemical known to the State of California
to cause cancer, and birth defects or other
reproductive harm. Wash hands after handling.
(California Health & Safety Code § 25249.5, et seq.)
14. The warnings, precautions, and instructions
discussed in this instruction manual cannot
cover all possible conditions and situations
that may occur. It must be understood by the
operator that common sense and caution are
factors which cannot be built into this product,
but must be supplied by the operator.
Fluid Type
The Pump is designed for use with water with
a maximum temperature of 77° F (25°C).
Do not use the pump for other fluids, especially not
fuels, cleaning fluids, or other chemical products.
Specifications
See Specifications for your model on included sheet.
Installation
The submersible motor pump must be installed
in a stationary position with either:
a. A fixed pipeline or
b. A flexible hose pipe.
Please note!
1. Do not install the pump by suspending it
unsupported from its delivery pipe or power cords.
The pump must be suspended from the
handle or be placed on the bottom of the shaft.
To ensure that the pump works properly,
keep the bottom of the shaft free from
sludge and dirt of all kinds.
2. If the water level sinks too low, any sludge in the
shaft will dry out and stop the pump from starting.
To help ensure the pump will start as required,
check the pump regularly with start-up tests.
Power Supply
1. The pump is equipped with a shock-
proof plug according to regulations.
The pump is designed to be connected to
120 V~, 60 Hz, Ground Fault Circuit Interrupter
(GFCI) protected safety socket.
2. Make sure that the socket is sufficiently
secured and is in excellent condition.
3. When the plug is inserted into the socket
the pump will be on standby.
4. Connect the Pump Power Cord only through the
Float Switch Cord plug to prevent dry running.