haier HWM90-0566 - Manual (Page 8)

>10mm
About less than 2mm after twisting
Figure 3
Connection between the water inlet hose jointer and the water faucet
Bushing
About 4mm before twisting
2. Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet.
See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen
the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth,
otherwise it may leak water. See to Figure 3.)
1. Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the
water inlet hose component. See to Figure 1.
Water faucet,not suitable
Install the water inlet hose
Screw
It is required that the front end shall be longer than 10mm.
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.
remark: Before installation, the threading is 4mmabove the upper surface of the nut.
After installation, the threading is 2mm above the upper surface of the nut. See to figure 6.
Figure 6
Sign plate
4 Take off the nameplate. Twist the fastening nut as per the indication of the figure
to seal up the exit end face of the faucet. See to Figure 5.
Figure 2
Screw nut
Screw knife
3. Fasten the four screws evenly. See to Figure 4.
water inlet hose jointer
Figure 5
Outlet end surface
Slider
Figure 1
Water faucet,suitable
water inlet hose
Figure 4
Lock level
Reserve, remain time digitron
It displays "--" during detecting.
It displays remained reserve time (hour).
It displays total remained time (min). If the total time
exceeds 99 minutes, it uses "A" on tens digit to
represent100 minutes, and uses "b" to represent 110
minutes. E.g. "A3" represents 103 minutes.
It displays abnormal symbol in abnormal situation.
(See to Page15)
Confirm the water faucet
• ••
•
•
•
•
TUB DRY button
Push the"TUB DRY"button,the
indicator is lighted,and the"TUB DRY"
function is operating. the"TUB DRY"
can not be selected after the
"program" button have been selected.
After washing,the innerand outer
tub is wet,mildew may grow not
using for a long time.Then,the
"TUB DRY" fuction can make the
tub dry preventing mildew from
growing. •
•
•
•
"Power" button
Push the "power" button to switch on the power.
Under power-on mode, push it to switch off the power.
Push the "power" button to switch on the power. If
the "start/pause" button is not pushed, the machine
will switch off the power automatically after 5 minutes.
Quick
Standard Tub dry
Jean
Normal
Posthaste
Fibre
Cotton
Woollen
Reserve Reserve
Water
level
Water
level
Program
Tu b d
ry
Tu b d
ry
Power Power
"Reserve" button
The digitron displays remain time
before washing is finished (in minutes)
Push "reserve" button, the digitron
displays the reserve time of washing
(in hours). The indicator flashes to
indicate that the reserve function
is operating.Push "reserve" button to
displaythe reserve mode.
WATER LEVEL button
The washing machine can detect the laundries automatically.
After detection, it will set the water level to suitable value among 4, 6, 8,
and 10 automatically.
You can also set water level by yourself. After the machine is started, it
will not set water level automatically. You shall push the start/pause
button to make new setting.
If there's water inside the tub, the machine cannot detect the laundries
and will display water level 6 .
If wet laundries are put in, it may display water level 10 . You must set
suitable water level by yourself.
If POSTHASTE programs selected, it will display water level 3 .
When water level 2 is reached in water filling, it will perform washing
while filling water. When water level 3 is reached, it will change to
normal washing.
During operation of wash and rinse program, you can push down the
water level button to add water. When you release the button, or it
reaches the overflow water level, the machine will stop adding water.
The water level decided may be different from actual value because of
the different moisture level of the laundries.
PROGRAM
STANDARD
QUICK
POSTHASTE
JEAN
FIBER
COTTON
WOOLLEN
NORMAL
PROGRAM selection button
Following automatic programs are available for selection
Applicable situation
Common washing
Washing the relatively big and thick laundries
Washing the chemical fiber laundries
Washing the cotton textiles
Washing the woolen textiles
Common washing
Quick and high-efficiency wash for common
laundries
Super quick wash of the laundry under 1 kg
with light soil