Edelbrock 1554 - Manual (Page 3)

Page 3
ADDITIONAL PARTS AND TOOLS
KIT CONTENTS
FOR STANDARD V-BELT DRIVE ACCESSORIES
❑ 1 Supercharger/Manifold Top Plate Assembly
❑ 1 Supercharger Intake Manifold
❑ 1 Supercharger Snout Support/Idler Pulley Bracket
❑ 1 Alternator Support Bracket
❑ 1 Idler Pulley
❑ 1 Idler Pulley Spacer
❑ 1 Idler Pulley Nut
❑ 1 Crankshaft Supercharger Drive Pulley
❑ 3 Crankshaft Pulley Shim
❑ 1 7/16-20 x 2.75” Long, 1.50” Shoulder Bolt (Crankshaft Balancer)
❑ 3 3/8-24 x 3.75” Long, 2.625” Shoulder Bolt (Crankshaft Pulley)
❑ 3 3/8-16 x 4” Long, 2.75” Shoulder Bolt (Idler Pulley and Bracket)
❑ 10 3/8-16 x 1.25” Long Bolt (Intake Manifold)
Standard Bolt Pattern Kits Only
❑ 2 3/8-16 x 1.75” Long, .625” Shoulder Bolt (Intake Manifold)
Standard Bolt Pattern Kits Only
❑ 4 5/16-18 x 1.75” Long Bolt (Intake Manifold)
Vortec/E-Tec Bolt Pattern Kits Only
❑ 4 5/16-18 x 2.5” Long Bolt (Intake Manifold)
Vortec/E-Tec Bolt Pattern Kits Only
❑ 8 1/4-20 x 1” Long Bolt (Manifold Top Plate to Intake Manifold)
❑ 4 5/16-18 x 1” Long Bolt (Manifold Top Plate to Intake Manifold)
Standard Bolt Pattern Kits Only
❑ 3 3/8” I.D. Split-Lock Washer
❑ 1 7/16” I.D. Split-Lock Washer
❑ 1 7/16” I.D. x .120 Thick Flat Washer
❑ 1 Supercharger Drive Belt
❑ 1 Intake Manifold O-Ring Seal (54” Long)
❑ 1 Intake Manifold Gaskets (Pair)
❑ 1 Carburetor Kit (800CFM Thunder Series AVS, Electric Choke)**
❑ 1 Carburetor Stud, Nut, & Washer Kit**
** Carburetor and associated hardware included in certain kits ONLY.
See “Applications” section for those kits that include carburetor.
FOR BILLET SPECIALTIES TRU TRAC PULLEY SYSTEM
❑ 1 Supercharger/Manifold Top Plate Assembly
❑ 1 Supercharger Intake Manifold
❑ 10 3/8-16 x 1.25” Long Bolt (Intake Manifold)
Standard Bolt Pattern Kits Only
❑ 2 3/8-16 x 1.75” Long, .625” Shoulder Bolt (Intake Manifold)
Standard Bolt Pattern Kits Only
❑ 4 5/16-18 x 1.75” Long Bolt (Intake Manifold)
Vortec/E-Tec Bolt Pattern Kits Only
❑ 4 5/16-18 x 2.5” Long Bolt (Intake Manifold)
Vortec/E-Tec Bolt Pattern Kits Only
❑ 8 1/4-20 x 1” Long Bolt (Manifold Top Plate to Intake Manifold)
❑ 4 5/16-18 x 1” Long Bolt (Manifold Top Plate to Intake Manifold)
Standard Bolt Pattern Kits Only
❑ 1 Intake Manifold O-Ring Seal (54” Long)
❑ 1 Intake Manifold Gaskets (Pair)
❑ 1 Carburetor Kit (800CFM Thunder Series AVS, Electric Choke)**
❑ 1 Carburetor Stud, Nut, & Washer Kit**
** Carburetor and associated hardware included in certain kits ONLY.
See “Applications” section for those kits that include carburetor.
TOOLS AND EQUIPMENT:
❑ Box and open end wrenches
❑ Socket set
❑ Distributor wrench
❑ Pliers (channel locks and hose clamp)
❑ Screw drivers (regular and Phillips)
❑ Torque wrench
❑ Hammer
❑ Gasket scraper or putty knife
❑ Timing light
❑ Vacuum gauge
❑ Rags
❑ Water bucket
❑ Paper and pencil
ADDITIONAL PARTS AND SUPPLIES:
❑ Gaskets-Edelbrock, or performance gasket equivalent
❑ Pipe plugs, if needed
❑ Edelbrock Gasgacinch (#9300)
❑ RTV High Temp silicone sealer or O/2 sensor safe RTV
❑ Masking tape
❑ Modeling clay or putty
❑ Chalk
❑ Radiator coolant
❑ Teflon thread tape or PST thread sealer or equivalent
❑ Thread locking compound such as Loctite™ (Red, Blue, or
equivalent)
❑ Supercharger & Accessory drive belt (for Billet Specialties
applications, see installation procedure for recommended part
numbers)
IMPORTANT NOTE: Edelbrock E-Force Supercharger kits do not include
the Billet Specialties Tru Trac Pulley System. These systems are available
seperately from Edelbrock and include a water pump, A/C compressor,
drive belt, alternator, and all the pulleys, brackets, and mounting
hardware necessary for a complete installation. These systems can be
purchased with a power steering pump as part #1565, or without as part
#1566.
©2013 Edelbrock LLC
Brochure #63-1551
Part #s 1551-1554, 15511-15541, 15611-15641
Rev. 6/4/13 - QT/mc