Edelbrock 1725 - Manual

Part #1711, 1712, 1713, 1715, 1716, 1718,
1720, 1721, 1722, 1723, 1724, 1725, 1726
Rev. 9/12/12 - QT/mc
©2012 Edelbrock LLC
Brochure #63-1721 1 / 6
110/130 FUEL PUMPS
Part #1711, 1712, 1713, 1715, 1716, 1718,
1720, 1721, 1722, 1723, 1724, 1725, 1726
INSTALLATION INSTRUCTIONS
®
PLEASE study these instructions carefully before beginning this installation. Most installations can be accomplished with common tools and
procedures. However, you should be familiar with and comfortable working on your vehicle. If you do not feel comfortable performing this installation,
it is recommended to have the installation completed by a qualified mechanic. If you have any questions, please call our
Technical Hotline at:
1-800-416-8628, 7:00 am - 5:00 pm, Monday through Friday, Pacific Standard Time.
IMPORTANT NOTE: Proper installation is the responsibility of the installer. Improper installation
will void your warranty and may result in poor performance and engine or vehicle damage.
DESCRIPTION: Edelbrock Fuel Pumps are for high performance street or street/strip use where there is a demand for high volume fuel delivery.
These pumps are compatible with GASOLINE FUELS ONLY. They have been thoroughly tested and proven to have flow capacity significantly greater
than other popular mechanical fuel pumps used for street and street/strip applications. Edelbrock 110/130 Fuel Pumps fit the following applications:
110 FUEL PUMPS
AMC V8 ...........................................................................#1716
Small-Block Chevrolet .....................................................#1721
Big-Block Chevrolet .........................................................#1722
Small-Block Chrysler .......................................................#1720
Big-Block Chrysler ..........................................................#1723
289-351W Ford ...............................................................#1725
390-428 FE Ford .............................................................#1724
429/460 Ford ..................................................................#1726
Pontiac V8 .......................................................................#1713 130 FUEL PUMPS
Small-Block Chevrolet .....................................................#1711
Big-Block Chevrolet .........................................................#1712
289-352W Ford ...............................................................#1715
429/460 Ford ..................................................................#1718
INSTALLATION PROCEDURE
NOTE: Installation of the mechanical fuel pump is the same as for OEM pumps. If uncertain of the procedure to follow for your particular vehicle,
consult the appropriate repair manual for your model vehicle. Note that the fuel inlet and outlet of the Edelbrock Street Performance Fuel Pump is
much bigger than original equipment (3/8” NPT). See next page for instructions on re-positioning the pump body for fuel line clearance.
IMPORTANT NOTES:
• Pump inlet and outlet ports are tapped to 3/8” NPT.
• For off-road or race applications, we recommend the use of a dust-shield between fuel pump and the nearest wheel, to prevent dirt
or debris from plugging the pump vent hole.
• 110 GPH Fuel Pump output fuel pressure is set at 6 psi. An external fuel pressure regulator is NOT REQUIRED in most cases.
• 130 GPH Fuel Pump output fuel pressure is set at 10 psi. An external fuel pressure regulator IS REQUIRED in most cases.
Edelbrock recommends the use of our regulators # 1727, or 8192. See our catalog or website for more details.
• On some 351-W Ford engines there may be casting flash on the front cover which will interfere with proper seating of your new fuel
pump. File this area flat for proper gasket seating.
• When installing fittings, we recommend a liquid teflon thread sealant be used. This will help prevent the fitting from galling and
ensure a proper seal. DO NOT use teflon tape. DO NOT over tighten the fitting as this can crack the housing and void the warranty.
WARNING: Any galling or cracking of the fuel pump housing due to over tightening will void the manufacturer’s
warranty.