GE 500 Series 30 Inch Slide-In Gas Range Owners Guide - Manual (Page 11)

49-2001187 Rev. 0
11
USING YOUR
APPLIANCE:
Settings
Settings
There are several settings on your range. To access and change these settings, press the Bake and Broil pads at
the same time and hold for three seconds. “OFSt” will appear in the display.
Scroll through the Settings menu using the + pad for up and the – pad for down until the desired feature is displayed.
To select a feature to change, or to confirm a change, press Start . To cancel a change and return to the Settings
menu, press Cancel pad. To exit the Settings menu, press Cancel again.
Adjust the Oven Temperature (OFSt)
This feature allows the oven baking temperature to be
DGMXVWHGXSWRž)KRWWHURUGRZQWRž)FRROHU8VH
this feature if you believe your oven temperature is
running too hot or too cold and wish to change it.
To adjust the oven temperature, enter the Settings menu
as listed above, then scroll through the features until
“OFSt” is displayed and press Start . A number between
DQGZLOOEHGLVSOD\HG8VHWKH +/- pads to set the
desired temperature adjustment. Press Start again to
save the temperature adjustment. Press Cancel to exit
the Settings menu. This adjustment will affect Bake.
Do not use thermometers, such as those found in
grocery stores, to check the temperature inside your
oven. These thermometers may vary 20-40 degrees.
Sabbath Warmer Setting (Sabb)
This feature allows the user to increase the Sabbath
Warm temperature if the oven is operating cooler
than desired. To adjust this feature Lo or Hi, enter the
Settings menu as outlined above and scroll through the
options until "Sabb" is displayed, then press
Start. Scroll
to the desired option and press Start again to confirm.
Press Cancel to exit the Settings menu.
Sound Volume (Snd)
This feature allows the oven tone volume to be adjusted
On and Off (OFF). To adjust the tone volume, enter the
Settings menu as outlined above and scroll through the
options until
“Snd” is displayed, then press Start . Scroll
to the desired option and press Start again to confirm it.
Press Cancel to exit the Settings menu.
End of Timer Signals (End tonE)
This is the tone that signals the end of a timer. The tone
can be continuous (Cont) or one repeating beep (bEEP).
A continuous setting will continue to sound a tone until
a pad on the control is pressed. A single setting (bEEp)
will sound just a single tone at the end of the timer. To
change the tone, enter the Settings menu as outlined
above and scroll through the options until
“End tonE” is
displayed, then press Start . Scroll to the desired option
and press Start again to confirm it. Press Cancel to exit
the Settings menu.
12-hr Auto Shut Off (12h Shut)
This feature turns off the oven after 12 hours of
continuous operation. To enable or disable this feature,
enter the Settings menu as listed above and scroll through
the options until
“12h Shut” is displayed, then press
Start . Scroll to the desired option and press Start again to
confirm it. Press Cancel to exit the Settings menu.
Fahrenheit / Celsius (dEg Unit)
The oven control is set to use Fahrenheit temperatures
(F), but you can change it to use Celsius temperatures
(C). To toggle between temperature measurements, enter
the Settings menu as listed above and scroll through the
options until
“dEg Unit” is displayed, then press Start .
Scroll to the desired option and press Start again to
confirm it. Press Cancel to exit the Settings menu.
Clock Display (CLoc diSP)
This feature specifies whether the clock appears in the
display. The clock display may be "On" or "OFF." To
change the display, enter the Settings menu as listed
above and scroll through the options until
“CLoc diSP”
is displayed, then press Start . Scroll to the desired
option and press Start again to confirm it. Press Cancel
to exit the Settings menu.
Clock Configuration (CLoc cFg)
This feature specifies how the time of day will be
displayed. You can select a standard 12-hour clock
(12) or 24-hour military time display. To change the
configuration, enter the Settings menu as outlined above
and scroll through the options until
“CLoc cFg” is
displayed, then press Start . Scroll to the desired option
and press Start again to confirm it. Press Cancel to exit
the Settings menu.
Remote Enable (APP EnbL)
(on some models or with U+ Connect
module)
Allows you to control your oven remotely. This feature
may be “on” or “oFF.” To change the configuration, enter
the Settings menu as outlined above and scroll through
the options until
“APP Enbl” is displayed, then press
Start . Scroll to the desired option and press Start again
to confirm it. Press Cancel to exit the Settings menu.