beautypg.com

Ipr2, 3000 specification sheet – Peavey IPR2 2000 2-Channel Power Amplifier User Manual

Page 106

background image

IPR2

3000 Specification Sheet

Rated Power 2ch x 2 ohms

1750 watts 20ms repetitive burst / 1450 watts 1% THD both ch. driven @ 1kHz.

Rated Power 2ch x 4 ohms

950 watts 20ms repetitive burst / 900 watts 1% THD / 815 watts 0.2% THD, both ch. driven @ 1kHz.

Rated Power 2ch x 8 ohms

525 watts 20ms repetitive burst / 500 watts 1% THD / 430 watts 0.15% THD, both ch. driven @ 1kHz.

Minimum Load Impedance

2 ohms

Maximum RMS Voltage Swing

70 volts

Frequency Response

20 Hz - 22 kHz; +/-.05dB @ 4 ohms

20Hz - 20kHz 2ch x 2 ohms

<0.15% @ 1,200 watts 20 Hz to 3 kHz, decreasing to 1,100 watts @ 20 kHz, both ch. driven.

20Hz - 20kHz 2ch x 4 ohms

<0.15% @ 650 watts 20 Hz to 20 kHz, both ch. driven.

20Hz - 20kHz 2ch x 8 ohms

<0.15% @ 375 watts 20 Hz to 20 kHz, both ch. driven.

Input CMRR

> - 76 dB @ 1 kHz.

Voltage Gain

x 75 (+37dB)

Crossover

100 Hz switchable 2nd order High pass and 3rd order Low Pass per ch.

Crosstalk

> -68 dB @ 1 kHz @ 400 watts @ 8 ohms.

Hum and Noise

> -101.5 dB, “A” weighted referenced to rated power @ 4 ohms.

Slew Rate

> 12V/μs

Damping Factor (8 ohms)

> 215:1 @ 20 Hz - 1 kHz @ 8 ohms

Input Sensitivity

0.775 volts +/- 3% for 1 kHz 4 ohm rated power, 0.730 volts +/- 3% for 1 kHz. 2 ohm rated power

Input Impedance

15 kilohms, balanced and 7.5 kilohms unbalanced.

Current Draw @ 1/8 in VA (watts)

960 (535) @ 2 ohms, 615 (315) @ 4 ohms, 400 (200) @ 8 ohms

Current Draw @ 1/3 in VA (watts)

2065 (1360) @ 2 ohms, 1215 (735) @ 4 ohms, 740 (420) @ 8 ohms

Idle Consumption

160VA, 75 watts

Cooling

Temperature dependent variable speed 80 mm DC fan.

Controls

2 front panel attenuators, crossover select switch for H.P.F, Normal and L.P.F.

Indicator LEDs

Five LED indicators per channel: Active, Signal, DDT

, Temperature and DC

Protection

Thermal, DC, subsonic, incorrect loads, under and over voltage

Connectors

Dual combination 1/4” XLR, dual male XLR input thru, two twist lock connectors

Construction

0.062” aluminum

Dimensions

3.5”x19”x 10.5” behind front panel + 0.6” for handle

Net Weight

5.62 kg (12.4 lbs.*)

Gross Weight

6.80 kg (15.0 lbs.)

Rated power readings made with BW: <10 Hz to 22 kHz. All power measurements made @ 120 VAC or 240VAC.
2 ohm steady state sine wave power is time limited by circuit breaker and AC limitations.
*Net Weight does not include power cord.

This manual is related to the following products: