PLANET DSP-1000 User Manual

Quick guide, Uv w x

DSP-1000
DSP-1000W

PLANET reserves the right to change specifications without prior notice. All brand names and trademarks are property of

PLANET Technology Corporation

11F, No. 96, Min Chuan Road, Hsin Tien, Taipei, Taiwan, R.O.C.

Tel: 886-2-2219-9518

Fax: 886-2-2219-9528

Email: [email protected]

www.planet.com.tw

2011-K20040-000

Quick Guide

DSP-1000

Power Adapter

Step 1. Copy Demo video files

Assume E drive is the CD-ROM drive and I drive is the CF Storage
Drive. Copy all the files in “E:\Demo” to the root directory of CF Storage.

Step 4. Network Connection

Step 5. Connect Power Adapter

Step 6. Install Batteries into Remote Control

Connect the Local Area Network where can provide the contents for future
updates.

Step 2. Install the Storage Device into DSP-1000

Gently slide in the CF Card that contains the files into the CF slot of
DSP-1000/1000W.

Step 3. Monitor Connection

Connect the A/V Cable to the RCA interfaces of the TV set.

TV Set

DSP-1000

Ethernet Switch

Ethernet Port

Manage PC

Content PC

Note: Batteries are not bundled in the package

After DSP-1000 / DSP-1000W boot up properly, you will see the Demo Video with 4 zones as
following figure.

Now, the DSP-1000/1000W has just finished its first installation.

Unified Office Gateway UMG-2000

Step 7. Turn on The DSP-1000 / DSP-1000W

Step 10. Show Demo Video

1. Please remove the power connection or switch off the power for your CF storage insertion

or remove. Without power off the device to insert or remove the CF card may cause device
malfunction.

2. Please read the following information of this guide for more of your DSP-1000. However, it

is also strongly recommended to read the user manual carefully for more advanced setting
of this powerful Digital Signage Player.

3. The files played in your TV set may not fully fit to the screen. It is not caused by your

DSP-1000 yet, you can just change your contents by resize your images or video files later.

Reminder

Step 8. Go to Main Menu

Turn ON the Power Switch, the LED light on with green
color.

System needs about 1 minute for system boot up.
If no display on TV set, use the remote controller to
point at IR receiver of the DSP-1000.
Then continue to click on ‘TV mode” button of the
remote controller 1 ~ 8 times until the screen displays

The unit will automatically reboot after the new settings have been uploaded.

BASIC INFORMATION OF DSP-1000

A. Default settings of DSP-1000 / DSP-1000W

The following is some of the default setting of your Digital Signage.

IP address

DHCP client

Monitor setting

C/S-Video

Zone

Single Zone

Adapter

CD-ROM

User’s Manual

YPbPr AV cable

Antanna

Remote Control

Bracket Package

VGA AV Cable

Quick Installation Guide

S-Video / RCA AV Cable

VERIFY THE CONTENTS INSIDE PACKAGE BOX

The package box should contain the items indicated below plus DSP-1000 / DSP-1000W.
If any item is missed or damaged, please contact the seller immediately

INSTALLATION REQUIREMENT

Ethernet Cable

x 6

x 1

x 2

Network Switch

A. Storage Device

B. TV

C. PC

D. Network Switch (option)

Note: In this guide we use CF

card for the first quick
installation. If you would like
to use HDD, pleaes refer to
user’s manual for more

Note: In this guide we require the PC

to copy the contents to the CF
Card for the first installation

128MB (at least)
2GB (or above suggested)

Note: In this guide we use RCA TV set as the setup example

TV set with RCA interface

TV-set with HDMI interface

2.5” SATA HDD

PC with
1. CD-ROM
2. CF Card Reader
3. LAN interface

BASIC INFORMATION OF DSP-1000

B. Default Zone Definitions

C. File Structure of Demo Folder

D. DSP-1000 Start up sequence

E. Config Tool installation

Your DSP-1000 will follow the CF storage files to play the contents. By default it is single zone, you
could change to three or four zones and DSP-1000 basically will follow the settings to play them.
4-Zone Display

AVI - motion file area

The motion file is located at root directory. And this file can manually replaced by editing the file
“play.lst”. The current file name used in this demo is “UMG2000.avi” in size 540 x 360 pixels at 30fps.

Title banner

The file is located at “\toppic” folder with the format JPEG (“.jpg” file). The current file name used in
this demo is “DSP.jpg” you can just replace this file to change your title banner.

Advertise picture area

Those files are located at “\pic” folder. You can just replace those files to change your advertise files.
However, for the timing setting, please install the “Config Tool” for more. The Config Tool can be
found in the CD-ROM.

Scrolling Message

For the scrolling message, you are required to use the Config Tool to change the scrolling text and the scrolling speed.

In the CD-ROM, there is also the

Config Tool utility, this utility will also help you to:

1. Setup the play list
2. Setup the scrolling message
3. Setup the picture rotation speed
4. And more advanced setup including

4.1. System setup like IP address, Screen setup, etc..
4.2. Zone division setup such as video screen on right or left.
4.3. Content Update setup such as interval, server location, type of download

Please also install this Config Tool utility into your management PC for advance
management of your installed DSP-1000 or DSP-1000W in your Local Area
Network.

1. Please make sure all the connections are well connected.
2. If the screen did not shows up the boot up screen please use the Remote Controller to check the TV mode.
3. Make sure the Play List is with correct file name according to the files in the storage.
4. If the played contents did not match the screen, please double check the image size of your files.
5. For Background Updates, please refer to the User Manual for more.

\pic: Advertise picture folder. DSP-1000 will play all the files in this directory continuously. The
default image size is 180 x 420 pixels with JPEG format. And it is also suggested to use

Config

Tool for the change timing of the pictures.

\toppic: Title banner image folder. The Title banner image default size is 540 x 60 pixels with JPEG
format

Play.lst: A text file that have the basic define of the files to play and play related settings. For the
first installation, please just keep the format. And later you can use

Config Tool for more settings.

Please refer to the user manual for more.

1. Power On

2. Set up Display Environment base

on the system configuration

3. Check the Play List

file (Play.lst)

4. Play the contents

accordingly

5. Background check the

Update Server

CFCard

Press navigation keys to select

Config icon and press the Enter key.

Select

Restore and press Enter on remote controller to load the settings.

Reminder

Step 9. Copy Configuration File

(DSP-1000W)