Euro-Pro BPV325H - Manual (Page 8)

OPERATING INSTRUCTIONS
6
OPERATING INSTRUCTIONS
7
2. Step on the floor to carpet selector
to adjust the height of the brushes.
There are two (2) different heights
one for floors and one for carpets.
(Fig. 12)
3. To remove the telescopic tube from
the floor to carpet brush, pull the
telescopic tube out from the floor
to carpet brush.
Using the Attachments
Dusting Brush
The dusting brush is used
for the furniture
Crevice Tool
Use for radiators, crevices,
corners, baseboards and
between cushions.
Pet Hair Remover Brush
The pet hair remover brush
is used for upholstery. The
unique surface makes it an
excellent tool for removing
unwanted pet hair.
Note : This tool is not a grooming tool
and should not be used on animals.
Caution: Do not use pet hair
remover brush on delicate or woven
fabrics that may snag.
DO NOT use pet hair remover brush on
wooden floors as this accessory might
cause mild scratching.
Blower Attachments
The blower attachments can be used
with the vacuum to pick up very fine dirt
particles in tight crevices or spots, or to
inflate inflatable items or air
mattresses.
Fig. 12
Floor to
Carpet
selector
Using the Air Driven Turbo Brush
Warning: To reduce the risk of electric
shock, the power cord must be
disconnected before removing the
HEPA dust bag, the shake-out bag,
HEPA pre-motor filter, changing the
filters or performing maintenance or
troubleshooting checks. The efficiency
of your air driven turbo brush depends
on the bristle brush rotating at high
speed. Strong air suction is needed to
accomplish this. In order to ensure that
maximum air suction is maintained,
please read the following instructions:
1. Change the HEPA dust bag or empty
the shake-out bag frequently.
2. Replace the pre-motor and exhaust
filters as needed.
3. Ensure that the rotating brush is kept
free of hair and string which may
accumulate and decrease brush
performance.
4. To attach the air driven turbo brush,
insert the telescopic tube into the air
driven turbo brush.
How To Clean the Air Driven
Turbo Brush
From time to time, the turbine of your
air driven turbo brush will require
cleaning. To do this:
1. Remove the turbo brush from the
telescopic tube.
2. Flip the turbo brush over so that the
bottom of it is facing upwards.
(Fig. 13)
Fig. 13
2. Remove the exhaust filter.
3. To place the blower port into the
exhaust outlet, align the lower tabs
on the blower port with the slots on
the exhaust. Pull up on the exhaust
tab and push the top of the blower
port until it snaps into place. (Fig. 17)
Fig. 16
Exhaust
Tab
Exhaust
Grill
Fig. 18
The blower attachments have air bleed
holes. These air bleed holes help relieve
some air pressure so that the attachment
does not blow off. However, should an
increase in air pressure be desired,
simply cover one or more of the air bleed
holes.
To use the blower attachments:
1. Pull up and hold the exhaust tab, with
the free hand pull out the exhaust
grill. (Fig. 16)
Fig. 17
Exhaust Tab
Blower
Port
4. To attach the hose to the blower
port, align the flexible hose and turn
counter-clockwise until it stops. The
hose is now securely in place.
(Fig. 18)
Using the Blower Attachments
The blower attachments are extremely
useful for vacuuming in hard to reach
crevices and small compartments such as in
cars.
Important Note: When blocking the air
bleed holes, grasp the blower attachments
firmly so that they do not blow off.
Note : Do not use blower function to clear
dust off of fragile or delicate objects unless
they are secured or held firmly in place as
the blower action is quite strong and could
cause damage.
3. Using your thumb and index finger,
simultaneously squeeze the locking
tabs on either side of the trap door
and lift off. (Fig. 14) Doing so will
remove the trap door and allow you
access to the turbine for cleaning
and maintenance purposes. (Fig. 15)
Locking
Tabs
Fig. 14
Trap Door
Turbine
Fig. 15
4. There may be some dust, lint, hair,
etc on the turbine wheel. Remove as
much of this as possible.
5. You may also use the unit’s hose with
the crevice tool attached and use the
vacuum to remove any additional
debris from the turbine.
6. Ensure that the turbine wheel moves
freely by rotating it with your finger. If
the turbine does not rotate, call EURO-
PRO Customer Service for help at
1 (800) 798-7398.
7. Once clean, replace the trap door of
the turbo brush. Ensure that it clicks
into place.